When you think of the railway DC DC converters and other similar converters where high, voltage conversion is necessary, the safety measure is a vital factor. High voltage design and manufacturing comes with the additional set of disciplines which a must that should be applied in order to produce an electronic component for long-term reliability. The high voltage electronic component generally works is low maintenance and harsh temperature. For getting the reliability in its use, the insulation and internal equipment, protection is essential.
The high voltage compatibility converters were not so simple and smaller as it is today. The larger converter transformer was used previously for maintaining the Entire system of railway department. Basically the converters are set in the engine room or sometimes to the special corridor of a compartment. They remain untouched for years, and they are kept them without any maintenance.
In the meantime, the power surge might go leakage and can make the entire compartment electrically surged. Then the entire compartment and its people face a great danger of electric shock. Sometimes, water might get splashed on it or any other liquid. Then, the product or converter might go damaged. This does not a question of only the damage of power converter, it might burst with a heavy boom and bang. This is the reason, while creating a converter for any purpose or for the purpose commercial reason; you have to maintain the entire system of commercial DC DC converter with great attraction.
With the passage of time, the technology is getting improved and the product size has been in shrinkage. Sometimes, price of the product is also getting down- sometimes high as the case may be. But, with the improvement of technology of its carnal circuit or conversion, the insulating system should also be in proper way, logically set and the material selection is essential.
If it is not a matter or electronic high voltage conversion in harsh accommodation, the entire system would easier to manage and control. Where a simple fault may bring you a great cause of blasting as well as the massive loss, you need to create it with great attention. On the other hand, whatever the converter is, either it is a large or a small one, you muse use a great heat sink to radiate the temperature to the atmosphere for keeping the entire system cool. An industrial DC DC converter should follow the same rule as all these consume and convert a high voltage and convert them according to the need. For working supremacy of the heavy system in all weather and accommodation, they are called rugged converters.
With the passage of time and the development of electronic conversion, the accuracy and the waste of the power is less now. The accuracy and conversion wastage is as low as about 95% to 98% is detected. Therefore, when you need to the best sort of products of rugged quality, the entire accuracy and long hour working ability should be measured. If the accuracy percentage is high and the power wastage is also low, the system will not be so hot and the use of heat sink will be less. Therefore, while choosing rugged DC DC converter, you must look for the modern service accuracy as well the power wastage percentage.
If you come back to the safety measure of the system, it is really tough to maintain when it receives and converts high voltage. The entire system become increasingly less in its size and miniaturizing. With the mastering of the thought and idea, makes the converter technology reach a further height. Failure to apply the technology properly applies these designs and manufacturing technology result in real world MTBF (Mean Time Between Failure) well below design expectation. This is why, the conductors, heat sink and insulation should also be in its better condition. Without the better hardware technology, the meantime between failures reduces and you will get least performance. If the system heat does not get radiated properly with the heat sink, the workability goes reduced. This is the reason, you should buy the converter from such a company where all these safety measures and product performance is justified.
Air is said to be an insulator. Lighting again proves that air is not always an insulator. When it is the matter of high voltage, you have to think deeply. If it is a matter or high voltage, you should think of the matter that high voltage could not be tamed like a caged powerful animal. It always tries to escape and find path to get the way, and so it is dangerous. Taming and controlling of high voltage is a matter of electronic engineers or it is a matter of physics.
Today, apart from converting the high voltage to other system is not so tough, but it is tough to protect with right insulator. In the modern age, you will find out so many insulator and protector to protect your entire system. Even after doing all these, the system fails to do and then the entire system feels a greater catastrophe.
Therefore, for getting the best sort of railway DC DC converters or any other type with right equipment for long duration, Karatec is the right place.
