1. DPCM modulator trainer kit.
2. DPCM demodulator kit.
3. Storage oscilloscope.
4. Digital multimeter.
5. Coaxial cables.
6. C.R.O. probes & connecting wires.
THEORY:
2. DPCM demodulator kit.
3. Storage oscilloscope.
4. Digital multimeter.
5. Coaxial cables.
6. C.R.O. probes & connecting wires.
THEORY:
In this DPCM redundancy is reduced from over all bit value will decrease and number of bits required to transmit one sample will also be reduced. This type of digital pulse modulation scheme is called differential Pulse Code Modulation.
The differential pulse code modulation works on the principle of predetection . The value of the present sample value is predicted from the samples. The predetection may not be exact but it is very close to the actual sample value , shows the transmitting of differential pulse code modulation system works on the principle of predetection. The present sample value is predicted but it is very close to the actual sample value.
PROCEDURE:1. Verify the circuit as per the circuit diagram.
2. Observe the output of the A.F. generator .it should be a Sine wave of 400 HZ frequency with 5Vp-p
3. Verify the output of the D.C. source.
4. Observe the output of the clock generator using C.R.O. it Should be 64 KHZ and 8 KHZ. Frequency of square Wave with 5Vp-p.
FOR MODULATION:
5. Keep the C.R.O. in dual mode .connect one channel to
8 KHZ signal and another channel to open outputs.
6. Observe the DPCM output with respect to the 8KHZ Signal.
FOR DEMODULATION:
7. Connect the DPCM signal to the demodulator input.
8. Connect the clock signal from transmitter to the receiver Using co-axial cable.
9. Observe the D/A converter output using storage Oscilloscope and compare with the original signal and Observe that there is no information loss in process of Conversion and transmission.
10 . similarly verify for different values of modulating Signal voltage .
PRECAUTIONS:1. Check the connections before switch on the power supply.
2. Avoid loose connections.
3. Observe the output on C.R.O and take the readings without parallax error.
RESULT:
VIVA-VOICE:1.What is the aim of the experiment ?
2. Wat is DPCM ?
3.What is PCM ?
4. What is the difference between DPCM & PCM ?
5.Why we need coding ?
The differential pulse code modulation works on the principle of predetection . The value of the present sample value is predicted from the samples. The predetection may not be exact but it is very close to the actual sample value , shows the transmitting of differential pulse code modulation system works on the principle of predetection. The present sample value is predicted but it is very close to the actual sample value.
PROCEDURE:1. Verify the circuit as per the circuit diagram.
2. Observe the output of the A.F. generator .it should be a Sine wave of 400 HZ frequency with 5Vp-p
3. Verify the output of the D.C. source.
4. Observe the output of the clock generator using C.R.O. it Should be 64 KHZ and 8 KHZ. Frequency of square Wave with 5Vp-p.
FOR MODULATION:
5. Keep the C.R.O. in dual mode .connect one channel to
8 KHZ signal and another channel to open outputs.
6. Observe the DPCM output with respect to the 8KHZ Signal.
FOR DEMODULATION:
7. Connect the DPCM signal to the demodulator input.
8. Connect the clock signal from transmitter to the receiver Using co-axial cable.
9. Observe the D/A converter output using storage Oscilloscope and compare with the original signal and Observe that there is no information loss in process of Conversion and transmission.
10 . similarly verify for different values of modulating Signal voltage .
PRECAUTIONS:1. Check the connections before switch on the power supply.
2. Avoid loose connections.
3. Observe the output on C.R.O and take the readings without parallax error.
RESULT:
VIVA-VOICE:1.What is the aim of the experiment ?
2. Wat is DPCM ?
3.What is PCM ?
4. What is the difference between DPCM & PCM ?
5.Why we need coding ?
This post first appeared on Electronics And Communication Engineering, please read the originial post: here
