Are you searching for absolute solutions to Reboot Comcast X1 DVR Box? If so then you should know that you have surely found the right place. Here you will be guided with proper steps and instructions that will help you get done with the process in no time.
Introduction
So now if your X1 DVR box does not feel right while working with it, it is not recording, does not have a signal, or is unable to access the guide then you would need to troubleshoot the issues. Well and to do so you must know that when you troubleshoot your Comcast X1 DVR box you would need to first reboot it. Moreover, you also need to keep in mind that when you reboot it would clear of any memory issues and then let the DVR start all over again with a clean slate. Besides restarting the DVR is usually the first step taken when troubleshooting the issues and most of the time it is often the only step needed.
Three ways to Reboot Comcast X1 DVR Box;
- Using the Help Menu
- Push the Power Button
- And pulling the Power Cable
Also, you should keep in mind that depending on when you restart your DVR; your recording might just be interrupted. Therefore if you are restarting while the DVR is recording then it would disrupt the recording. Hence this action can let the already recorded and scheduled recordings and also preferences get lost.
Tools required;
- Paperclip
- An iPhone charging cable
- Get access to a computer which has iTunes installed already
- And any other non-consumable tools required
- You should comment out the tools section if no tools are necessary
Supplies needed;
- Zip ties needed
- Other consumable supplies
- You can comment out the supplies section if there are no supplies required
Before starting;
- Make sure to be near your cable box
How to Reboot Comcast X1 DVR Box using the Help Menu?
Now if you already have access to it then the help menu is the easiest way for Restart Comcast X1 DVR Box.
- You would need to start by pressing the help menu. And then you have to look for the ‘A’ button that is in the triangle.
- The XR15 Remote
- XR11, XR5 Remote
- XR2 Remote
- Silver Remote
Now under the troubleshooting section, you will need to select the ‘Restart’ button.
- Here you need to select the ‘Restart’ button to confirm.
Rebooting the DVR Using the Power Button
In case you cannot reach the ‘Help Menu’ or it does not work then you can choose to use the button that is in front of the DVR.
- To do so you would need to push and hold the ‘Power’ button that is right on the front of your cable box for about 10 seconds.
- Motorola DCH3416, DCH6416
- Motorola DCT3400
- Motorola DCT6208
- Motorola RNG200N
- Motorola DCX3400
- After doing so the cable box will restart. You then need to allow a few minutes for the cable box to finish starting back up.
Rebooting the DVR by Pulling the Power Cable
Now if you find that neither the ‘Help Menu’ nor the ‘Power’ button is working out then you should just remove the power plug from the box itself.
- To begin with, you will need to first unplug your cable box.
- And then you should wait for about 10 seconds.
- After that, you must plug your cable box back in.
- You just need to push the ‘Power’ button on your remote to turn your cable box back on.
You will now have the cable restarting; just allow a few minutes for the cable box to complete the starting backup.
Conclusion
Now that you have finished going through the above steps we hope that you have all your concerns resolved. And you know how to Reboot Comcast X1 DVR Box without any difficulty. Furthermore, if you need any related assistance then you can feel free to get in touch with the team of diligent experts provided right here. The team will be available at any time to guide you accordingly with the most suitable solutions.
Related Article: How to instantly configure the Outlook settings for Comcast email?
The post Restart your X1 TV Box with X1 AnyRoom DVR service appeared first on Local Geeks Tech.
