If you’re a proud owner of a Galaxy Watch 4, you probably know that Samsung’s smartwatches are top-notch. They run on WearOS, an Android-based system, which means you can tweak and customize your watch to your heart’s content. It’s like opening a treasure chest of cool features.

But here’s the catch. Sometimes, all these tweaks and customizations can backfire, and your watch might end up in a bit of a pickle. Some users have found themselves in a sticky situation – their beloved Galaxy Watch 4 gets stuck in a bootloop. What’s a bootloop, you ask? It’s when your watch keeps showing the Samsung screen over and over, like it’s stuck in a never-ending Loop.

To make matters worse, even when they try to turn off the watch and plug it in for charging, it doesn’t behave as it should. Instead, it goes right back into that frustrating boot loop. Even attempting to boot into Recovery Mode doesn’t seem to help.

If you’re nodding your head in agreement because you’re facing the same headache, don’t worry. This guide is here to rescue you. We’ll show you a clever workaround that should help you get your Galaxy Watch 4 out of this sticky situation. So, stick with us, and let’s get your watch back on track.

What Causes Samsung Galaxy Watch Keep Restart in Boot Loop?

Understanding what could have triggered your Samsung Galaxy Watch to get stuck in a never-ending reboot loop can be crucial in finding the right solution. Here are some common culprits:

• New Apps and Updates: One of the primary reasons your watch might be stuck in a boot loop is because of new apps you’ve installed, especially third-party ones, or updates to existing apps. These changes can sometimes throw your watch into a loop.
• Water Exposure: Water can be a sneaky troublemaker. If your watch has been swimming with you, taken an accidental dip in water, endured a super sweaty workout, or even soaked in a long, hot shower, it could be the cause of the boot loop.
• Firmware Updates: Occasionally, after updating your watch’s firmware, it might decide to act up and get caught in a boot loop. It’s rare, but it happens.
• Dirt and Debris: If your watch has become a bit grimy or sticky, trapped debris might be causing your power button to act up, leading to the reboot loop.

So, take a moment to think about what you’ve been up to with your watch recently. Have you added new apps or updated existing ones? Did your watch’s firmware recently get an update? Has it had any encounters with water or sweat? Is it looking a little dirty? Knowing this can help us pinpoint the right solution to break free from that frustrating reboot loop.

Simple Steps to Fix Samsung Galaxy Watch Keep Restart in Boot Loop

If you’re stuck with your Galaxy Watch 4 endlessly showing the Samsung logo and you’re not a tech wizard, don’t worry! We have a simple solution that doesn’t involve complicated stuff like soldering wires, bootloader unlocking, or firmware flashing via Netodin. Here’s what you can do:

Step 1: Let Your Watch Battery Run Out

First, leave your watch on the screen where it’s stuck (that’s the Reboot Mode screen) and allow the battery to completely die. Make sure it’s completely, totally, 100% dead.

Step 2: No Battery Screen Allowed

When you try to turn it on, don’t even let it show the 0% battery screen. Keep it off.

Step 3: Charge It Up

Now, grab your magnetic charger and pop your watch on it. Let it charge up completely.

Step 4: Power It Up

Once it’s fully charged, your watch should start up and boot to the operating system. If it doesn’t, you can also manually turn it on using the power buttons.

And that’s it! Those were the simple steps to fix your Galaxy Watch 4 when it’s stuck in a bootloop. Your watch should be back to normal in no time!

Absolutely, I understand how incredibly frustrating it can be when your Samsung Galaxy Watch gets stuck in that never-ending reboot loop. It’s like a never-ending cycle of shutdown, the hopeful “Rebooting…” screen, and then back to square one.

But don’t despair, we’re not throwing in the towel just yet. There are some steps you can take to break free from this maddening loop and bring your Galaxy Watch back to life. So, let’s dive right into the solutions and get that watch back on your wrist where it belongs.

Troubleshooting Tips for When Your Samsung Galaxy Watch Gets Stuck in a Boot Loop

So, your Galaxy Watch is stuck in that annoying reboot loop, and you’re wondering how to fix it. Well, the solution depends on what you think might have caused the problem in the first place. Let’s break it down:

Step 1: Suspect the Cause

First, think about what might be behind this issue. Did you recently do something like add new apps or update existing ones on your watch? Did it get wet, or is it looking dirty? These clues will help you narrow down the solution.

Step 2: Go Through the List

If you’re not sure what caused it, don’t worry. We’ve got a list of troubleshooting steps to try out.

Step 3: App Troubles

Sometimes, it’s an app that’s misbehaving. Here’s the tricky part: you can’t uninstall apps from the Galaxy Wearable app on most watch models. You have to do it directly on the watch. But here’s the problem – you can’t do that when your watch is stuck in a boot loop.

Step 4: If It’s an App

If you suspect it’s an app causing the problem, don’t fret. We have other methods to tackle it, even if you can’t uninstall apps the usual way.

So, let’s get started and figure out how to get your watch back on track, no matter what’s causing that pesky boot loop.

Clean and Dry Galaxy Watch

Keeping your Samsung smartwatch clean and button-ready is a smart move. Here’s how to do it without any fancy equipment:

Step 1: Gather Your Supplies

Grab a microfiber cloth or any lint-free cloth. You know, the kind you’d use to clean your glasses.

Step 2: Wipe It Down:

Carefully wipe your watch and, most importantly, those buttons. Make sure to give them some extra love.

Step 3: Dry It Out

If your watch recently had a swim or met some liquids, make sure it’s dry. You can use an absorbent cloth or just let it hang out in front of a fan. But please, don’t put it in direct sunlight – indirect sunlight is okay.

Step 4: Button Check

Press the buttons. They should give you a satisfying click. If they feel a bit mushy or unresponsive, don’t fret.

Step 5: Debris Check

Use your cloth or grab a soft toothbrush or even an interdental brush (like those tiny brushes for your teeth). Clean around the buttons and get rid of any trapped gunk.

Step 6: Keep at It

Keep cleaning until those buttons click confidently. You can even press them in and out a few times to shake out any lint or debris that’s hanging around.

By following these simple steps, you’ll keep your watch spick and span, and those buttons will be in tip-top shape, ready for action. No need for any fancy cleaning gear!

Force Restart Galaxy Watch

If you have a hunch that a recent firmware update or installing a new app (or updating an existing one) might be causing the boot loop, here’s a trick to try:

Forced Restart: Sometimes, giving your watch a good old-fashioned restart can work wonders, especially when the boot loop began right after you did something like installing an app or updating your watch’s software.

Now, there are a couple of ways to restart your watch. Let’s start with the easiest one:

Method 1: Press and Hold the Power/Home Button

Step 1: Look for the button on your watch that typically serves as the power or home button. Hold it down and don’t let go for about 10 seconds.

Step 2: While you’re holding it, keep an eye on your watch’s screen. After a little while, you should see a message that says “Rebooting…”. Once that message pops up, you can release the button.

Step 3: Now, be patient. Wait and see if your watch starts up like it should, showing your watch face. It might take a few minutes to fully restart, so resist the urge to press any buttons or tap the screen while it’s doing its thing.

If your watch still refuses to cooperate and remains stuck in that boot loop, don’t worry. We’ve got more tricks up our sleeves to help you out. Let’s move on to the next method.

Method 2: Press and Hold the Power/Home and Back Buttons Together

Let’s keep troubleshooting that Samsung Watch of yours. If the previous method didn’t do the trick, no worries. We have another one for you:

Step 1: Find the power or home button on your watch (it’s usually on the side) and the back button (often below the screen). Hold both of these buttons down at the same time.

Step 2: Keep holding them until you spot a message that says “Rebooting…” on your watch’s screen. Once you see that, you can let go of both buttons.

Step 3: Now, here’s a little twist. If your watch’s screen displays options like “Power off,” “Turn off,” or “Restart,” don’t release those buttons just yet. Keep on holding them down until you see that magic word, “Rebooting…” – it might take about 30 seconds or even more.

Step 4: Be patient. Wait and see if this forced reboot works its magic. If all goes well, your watch should eventually show your watch face, and you’ll be back in business.

If you’re still stuck in that stubborn boot loop, hang in there; we’ve got more tricks coming your way.

Method 3: Utilize Reboot Mode

Let’s explore yet another method to tackle that boot loop on your Samsung Watch. This time, we’ll use something called “Reboot Mode.” Here’s how it goes:

Step 1: Find your watch’s power or home button and the back button (usually below the screen). Hold down both of these buttons at the same time.

Step 2: Keep holding them until you spot the word “Rebooting…” on your watch’s screen. When you see it, let go of both buttons.

Step 3: Now, here’s the tricky part. If your watch screen shows options like “Power off” or “Restart,” don’t release those buttons just yet. Hang on to them until you see that “Rebooting…” message – it might take a little while.

Step 4: Once you’ve done that, quickly press the home or power button repeatedly. Do this until you see the Reboot Mode menu on your watch’s screen.

Step 5: The first option on the menu should be “Continue.” It might already be highlighted, but if not, you can move between menu items by pressing the home or power button.

Step 6: Now, select “Continue” from the menu. If you accidentally select “Power Off,” that’s okay too; we can work with that.

Step 7: Hold down the home or power button again to reboot your watch, and keep holding it until your watch starts the rebooting process.

Step 8: If your watch is still playing hard to get and stays stuck in that boot loop, don’t give up just yet. Place it on its charger and try the “Power Off” option instead of “Continue.” Once it powers off, you’ll need to turn it back on.

And if that doesn’t do the trick, don’t worry; we have more steps to try. Keep going with the troubleshooting – we’ll get your watch back on track.

Clear the Cache for Galaxy Wearable app and the Galaxy Watch

Here’s a neat trick that might help if your Samsung Watch is stuck in a boot loop – we’re going to clear out some “cache.” Don’t worry; it’s easier than it sounds.

Sometimes, your watch can get stuck in a boot loop because it’s holding onto some old data (that’s what we call cache) that’s causing trouble. Here’s how to clean it up:

• Start by clearing the cache for the Galaxy Wearable app. Think of this app as the control center for your watch. Open it up and find the option to clear the cache. This step is the same for all watch models.
• If you’re using a Wear OS 3 watch (like the Samsung Galaxy Watch 4 or 5), there’s an extra cache-clearing trick. Remember that Reboot Mode we used earlier? Well, there’s an option in there to clear the cache on the watch itself. Give that a shot.

Clearing out this cache can fix all sorts of problems, including the boot loop issue and any other performance hiccups your watch might be experiencing. So, it’s like giving your watch a little spring cleaning to make it run smoother.

Clear the Wearable App’s Cache

Step 1: Open the Settings app on your phone. It’s the one that looks like gears or cogs.

Step 2: Scroll down and find “Apps” or “Applications.” It’s where all your apps live.

Step 3: Look for the Galaxy Wearable app in the list of apps on your phone. When you find it, tap on it.

Step 4: Now, you’ll see an option called “Storage & cache.” Go ahead and select it.

Step 5: Finally, tap on “Clear cache.” It’s like giving your app a little refresh by getting rid of any unnecessary data.

And that’s it! You’ve successfully cleared the cache for your Galaxy Wearable app. It’s like decluttering your digital closet to make things run smoother.

Clear Your Galaxy Watch’s Cache

If you’re using a Wear OS 3 watch like the Samsung Galaxy Watch 4 or 5 and want to clear the cache (basically, tidy up some digital mess), follow these steps. Unfortunately, these functions won’t work for Tizen watches like the Active 2 or Galaxy Watch 3.

Step 1: First, press and hold both the home/power button and the back button on your watch. Keep holding them until you see the word “Rebooting…” appear on your watch’s screen. If you see options like “Power off” or “Restart,” keep on holding until you see “Rebooting…”

Step 2: Next, quickly tap the home/power button multiple times. Keep doing this until you see a menu called “Reboot Mode” pop up on your watch’s screen. It’s like unlocking a secret door.

Step 3: In this menu, use the home/power button to move down the list of options. Find and highlight “Recovery,” then press and hold the home/power button again. Release it when the screen goes black. It’s like picking the right book from the library shelf.

Step 4: Now, wait a bit. Your watch will show you another menu soon.

Step 5: Use the back button on your watch to go through the options on the screen. You want to pick “Wipe cache partition,” so make sure it’s highlighted. Once you’ve done that, press and hold the home/power button again.

Step 6: There will be a confirmation message. Press the back button once to say “Yes,” and then hit the home/power button to confirm. It’s like saying “Yes, I want to clean up.”

Step 7: Hang tight while your watch does some cleaning. It will clear out that cache and take you back to the previous menu.

Step 8: Lastly, choose “Reboot system now” from the menu by pressing the home/power button. It’s usually already selected, but if it’s not, use the back button to move between options.

And there you have it! Your watch’s cache is now clean and tidy, ready to run smoother. It’s like giving your watch a fresh start.

Clean Up Memory and Storage using Wearable app

Let’s clear up some memory and storage on your Samsung watch to help with that boot loop issue. These steps are for Tizen watches like the Active 2 or Galaxy Watch 3, not for Wear OS 3 watches like the Galaxy Watch 4 or 5.

Step 1: Start by opening up the Galaxy Wearable app on your phone. It’s like the command center for your watch.

Step 2: Depending on your watch model, you might see an option like “Watch settings.” If you do, tap on it.

Step 3: Now, scroll down and look for “About watch.” This is where you’ll find important information about your watch.

Step 4: You’ll see an option called “Memory.” This is what’s helping background apps run on your watch. Tap it.

Step 5: Wait a bit for your watch’s memory info to load up. Once it’s ready, tap the “Clean” button. Think of it like clearing away all the extra stuff to make your watch run smoothly.

Step 6: Now, go back to the “About” menu and do the same thing for “Storage.” This will delete any temporary and unnecessary files that might be clogging up your watch’s storage space. Don’t worry; your important data will stay safe.

By following these steps, you’re giving your watch a little digital spring cleaning. It’s like tidying up your room to make it feel more spacious and comfortable. This should help with that boot loop problem, and you won’t lose any of your important stuff.

Reset Your Galaxy Watch Using Recovery Mode

If you’re still facing problems with your Galaxy Watch and nothing else seems to work, there’s one last resort you can try.

Now, this is like hitting the reset button, but it’s more powerful. When you use the Recovery Mode’s recovery option, your watch goes back to how it was when it first came out of the box. That means everything you added – personal data, settings, and even third-party apps – gets wiped clean.

So, be absolutely sure you want to go through with this because there’s no turning back once you start.

Backup Your Watch (If You Can)

Before taking the big step of resetting your Galaxy Watch in Recovery Mode, it’s a smart move to try and back up your important stuff if you can. It might not always be possible, but it’s worth a shot.

Open up the Galaxy Wearable app on your phone. It’s your go-to tool for managing your watch.

Step 1: If your app connects with your watch, look for “Watch settings.” Give it a tap.

Step 2: Next, find “Account and backup” and select it.

Step 3: Here’s where you’ll see an option to “Back up data.” Go ahead and tap on that.

Step 4: If it lets you choose what to back up, go for “Select all.” This way, you’ll save everything you can. Then, hit “Back up.”

Step 5: Now, give it a little time to work its magic. The Wearable app will do its thing and create a backup of your data.

It’s like making a copy of all your important files, just in case. So, if you ever need to reset your watch in Recovery Mode, you won’t lose your precious data.

Reset Your Galaxy Watch Using Recovery Mode

Here’s how you can use Recovery Mode to reset your Galaxy Watch, but please keep in mind that this is like hitting the reset button, so you’ll lose all your personal data and settings. If you were able to back up your watch’s data, great! If not, you might need to set it up again from scratch.

Step 1: Press and hold both the home/power button and the back button on your watch. Keep holding them until you see “Rebooting…” on your watch’s screen. If you see options like “Power off” or “Restart,” hold those buttons until it says “Rebooting…”

Step 2: Quickly tap the home/power button multiple times. This should bring up a menu called “Reboot Mode” on your watch’s screen.

Step 3: In this menu, find and select “Recovery.” It might be one of the last options, so use the home/power button to move through the list and choose it.

Step 4: If you’re using a Wear OS model like the Active 2 or Galaxy Watch 3, your watch will start the recovery process automatically. Skip to Step 9.

Step 5: If you’re using a Wear OS 3 model like the Galaxy Watch 4 or 5, there will be another menu. Swipe down or use the back button to highlight “Wipe data/factory reset,” then press the home/power button to choose it.

Step 6: Next, swipe down or use the back button again to highlight “Factory data reset.” Press the home/power button to confirm.

Step 7: Wait for the reset process to finish. It’s like giving your watch a clean slate.

Step 8: Once it’s done, press the home/power button again to reboot your watch. It’s like turning it on for the first time.

Step 9: After your watch resets and boots up, open the Galaxy Wearable app on your phone. This is where you can set up your watch again and, if you were able to back up your data earlier, you can restore it now.

So there you have it! Your watch is reset, and it’s like starting fresh. Just follow the steps to get it back to the way you like it.

Drain and Recharge the Battery

If you’ve tried everything and your Samsung Galaxy Watch is still stuck in that reboot loop, there’s one more thing you can try – and it’s a bit like giving your watch a full reset. Here’s what to do:

Step 1: First, take your watch off the charger and let it be. Allow it to use up all of its battery power until the screen doesn’t turn on anymore. This is like letting your watch run out of energy completely.

Step 2: Once it reaches that point where it can’t even turn on anymore, it’s time to give it a good, long charge. Put it back on its charger and let it juice up overnight if possible, or at least for a good 3-4 hours. Don’t try to use it or turn it on during this time. Just let it charge like it’s getting a full night’s sleep.

Step 3: After it’s had a good, long charge, try pressing the home/power button. If all goes well, your watch should turn on and boot up normally, like it did when you first got it.

This method has helped some folks break out of that reboot loop, so it’s worth a shot. It’s like a reset for your watch’s battery, and sometimes, that’s all it needs to get back on track.

Dry Out Your Watch

If your Samsung Galaxy Watch got wet and now it’s stuck in a boot loop, don’t worry, there’s still hope. Here’s what you can do:

Step 1: If you know or even just suspect that your watch got wet, the first thing to do is turn it off (if it’s still working). This is like putting your phone in rice when it gets wet – it helps dry things out.

Step 2: Find a container – it could be a small box or even a plastic bag – and toss in some desiccant packets if you have them. You know, those tiny silica gel packets that come with electronics and other stuff. If you don’t have those, don’t worry, there’s another option.

Step 3: Place your watch in the container with the desiccant and seal it up. Leave it in there for at least a day, maybe more. Think of it as your watch taking a nice, long nap in a dry environment.

Step 4: If you don’t have desiccant packets, you can try this instead: Put your watch near a fan that’s blowing room-temperature air. Don’t use heated air – it’s too hot for your watch. Think of it like letting your watch sit in front of a gentle breeze.

Step 5: After your watch has had a full day (or more) to dry out, give it a shot. Try turning it on and see if it boots up like it should. You might need to charge it first before it wakes up.

Now, here’s the thing – water and liquid damage aren’t covered under Samsung’s warranty. Surprising, right? So be extra careful around liquids, even though most Samsung watches are water-resistant, they’re not waterproof. That means you can’t take them swimming or dunk them in water like you would with a waterproof watch. It’s an important distinction to keep in mind, especially if you ever need to get your watch repaired.

Contact Samsung Support or Visit a Repair Center

If none of the previous steps managed to rescue your Samsung Galaxy Watch from its never-ending reboot loop, don’t lose hope just yet. It’s time to get in touch with the professionals who can sort it out for you.

Step 1: Head on over to Samsung’s support website. Look for the section dedicated to Mobile and Wearables.

Step 2: Select your specific watch model from the list. This way, you’ll be sure to get the right help for your watch.

Step 3: Sometimes, the issue might be something more serious, like a battery problem that needs replacing. But it could be something else entirely. Let the experts figure it out for you. Take your watch to a local smartwatch repair center if there’s one nearby. They have the skills and tools to diagnose and fix the issue.

Don’t worry; you’re not alone in this. The experts at Samsung support or your local repair center will do their best to get your watch back in tip-top shape. Sometimes, it just takes a professional touch to get things working again.

Summary

Here’s a summary of all the steps and tips for dealing with a Samsung Galaxy Watch stuck in a boot loop:

Troubleshooting Steps for Samsung Galaxy Watch Stuck in Boot Loop:

1. Restart Your Watch: Begin by trying a regular restart to see if that fixes the issue.
2. Check for Software Updates: Make sure your watch’s software is up to date as updates can often resolve problems.
3. Charge Your Watch: Ensure your watch has sufficient battery charge as a low battery can cause issues.
4. Boot in Safe Mode: Boot your watch in safe mode to see if third-party apps are causing the problem.
5. Uninstall Problematic Apps: If safe mode works, uninstall any recently installed or problematic apps.
6. Clear Cache and Data: Clear cache and data of any troublesome apps that could be causing the boot loop.
7. Factory Reset Your Watch: If nothing else works, consider a factory reset to return your watch to its default settings.
8. Update Your Watch: Ensure that your watch’s firmware is updated to the latest version.
9. Use Samsung Find My Watch: If your watch is linked to your phone, use Samsung’s Find My Watch feature to locate and troubleshoot it remotely.
10. Contact Samsung Support: If all else fails, get in touch with Samsung support or visit a local smartwatch repair center for professional assistance.

Remember, it’s essential to back up your watch’s data whenever possible and be cautious around water, as liquid damage isn’t covered under warranty. These steps should help you resolve the boot loop issue and get your Samsung Galaxy Watch back in working order.

Conclusion

In conclusion, dealing with a Samsung Galaxy Watch stuck in a boot loop can be frustrating, but there are several effective troubleshooting steps to resolve the issue. Starting with simple restarts and software updates, you can progressively work through the more advanced solutions, such as safe mode, app management, and even factory resets.

Remember to back up your watch’s data whenever possible and exercise caution with liquids, as water damage isn’t covered under warranty. If all else fails, reaching out to Samsung support or visiting a professional repair center is a viable option.

With these steps and a little patience, you can often rescue your Galaxy Watch from the boot loop and enjoy its features once more.

The post Solved: How to fix Samsung Galaxy Watch keep restart in boot loop appeared first on PUPUWEB - Information Resource for Emerging Technology Trends and Cybersecurity.