I have a 2018 TW450E that runs in my yard and slow good just will not go down the road seems to be running out of fuel where should i start? I have replaced both fuel and air filter drained… Read More
I have a Bennche 700 EFI Bighorn. I’ve recently been unable to get it to start. After a little troubleshooting I realized my fuel pump was not pumping fuel. This weekend I emptied the… Read More
I have a 2014 landmaster S/S 4x4 model 653 4x4 with a 22 hp robins engine. I've been having problems with the govenor reving after it running a short distance. I cleaned the carb and discove… Read More
I purchased a 2008 Qlink Rodeo 700 a few years ago. I am from Michigan. Anyone know of any local repair shops? I had a dead battery, so I replaced that, started right up, ran the quad dow… Read More
View File
Hisun HS400/Coleman UT400 Parts Diagrams
Compiled document with parts diagrams for Hisun HS400/Coleman UT400 for help in repairs where the service m… Read More
I have a hisun 500 got from a auction and when turning a corner left or right it's a two hand job then when you left go snaps back.any help on what to look at would be appreciated.
Also… Read More
(posted a similar question to the Hisun folks) Looked at a lot of UTVs lately. Couple Questions about Massimo. Some people say they are just cheap with no customer service. Other people seem… Read More
Looked at a lot of UTVs lately. Couple Questions about Hisun. Some people say they are just cheap with no customer service. Other people seem to have no problems with them.
Any opinions… Read More
Hello I am new here but have had this machine for about 5 years. I am having issues with it surging and sometimes sounding like a small backfire thru the intake. When putting in low, high o… Read More
I've been looking at various types of UTVs in the 400-700cc range. It seems that Massimo has a really good price point but I don't know much about their reliability and availability of parts… Read More
Mine is overheated/burned/melt at connection with its wire connector, parts are ordered to replace both them. This seems to be a common issue, and some of you already replaced it. I right n… Read More
Good day all,
searching here but cannot find the answer, Hisun been working fine and now reverse limiter seems to be engaging and cannot back up, cannot find a clear solution to disab… Read More
Good day all,
searching here but cannot find the answer, Hisun been working fine and now reverse limiter seems to be engaging and cannot back up, cannot find a clear solution to disab… Read More
Hey guys! Newbie here. I'm an old man who's better with plowing a mule (4-legged kind) than these newfangled beasts. I, and a friend of mine, just bought new Coleman sxs and are having to fi… Read More
I've installed the Kemimoto
side by side mirrors in my UTV to replace one that would not stay in place.This one give great views and tightens down nicely, but you have to take them down e… Read More
I've installed the Kemimoto side by side mirrors in my UTV to replace one that would not stay in place.This one give great views and tightens down nicely, but you have to take them down even… Read More
I have a DesertCross 800 that doesn't want to stay in low, it pops out when I let off the gas. No problem with the other gears. What do I need to do? Thanks Read More
Hello,
Before I invest $10k+ into a brand new UTV for the farm, I want to get my feet wet with a fixer upper and learn the mechanical side of things. I acquired a 2022 Hisun Axis 500 (L… Read More
I bought a tracker 88sx crew in 2023. It has a whishing noise coming from the front end. Starts out low and gets louder as speed increases. Took it back to the dealer and they said it was no… Read More
I have a Massimo 400 Buck that overheats and the antifreeze blows out of the motor everywhere! I don’t have to be doing anything but just driving through the field. It only has 26 mil… Read More
Has anyone ever had a Massimo 400 Buck that overheats and the antifreeze blows out of the motor everywhere? I don’t think the fan is turning to cool the motor. Any ideas how to fix t… Read More
At the end of last year my Coleman UT 500 will not go into reverse. I can hold it over toward the reverse to move it nut it won't lock into reverse. Anyone have this problem? Winter is just… Read More
Bought a Massimo 500 last night. Stopped and filled it up on the way home and I put the wrong gas in it. Is there a drain plug on the bottom of the tank that I can get to or will I have to s… Read More
Hey guys! My name is Bryan and i am the owner and creator of Safe Sled. Not some crazy corporate backed recovery product, but just some guy with an idea.
4 years ago, I suffered 11… Read More
Hey all. I need to change my plug in my ut400 and I remember seeing people in here saying to get a certain one that was better than what it came with. What was it?
Also I need to do an… Read More
This is my first buggy. I rode a Arctic Cat 500 manual for 19 years. My question is: with the engine running in Park and you rev the engine is the drive belt engaged and turning 🤷 Read More
starts up you have keep rpms up for 5 minutes till it warms up then runs fine. But if it stalls wont start unless you unplug fuel pump and hold it to the floor till it starts then plug pump… Read More
Have a Hisun 750 only 700hrs 21 model. Never had issues went to start it and there's a clicking sound under the seat I'm assuming it's the started relay. I for the life of me cannot find the… Read More
I replaced the fuel pump, ended up with a couple bad ones. This last one now worked fine for about 150 miles, now only works when its cool outside. (30-40). As soon as we hit 55 degrees, It… Read More
Hey Admins - What's with all the advertisements lately? This is so bad that it seems there are more ads than posts and I find it hard to follow a post because of all the ads slipping in betw… Read More
Hey all!
I'm on a mission to buy my first UTV soundbar as a gift for my dad. I'm aiming for something that offers great sound quality without breaking the bank – my budget is around… Read More
My 2018 Hisun sector crew engine cut off after about 15 minutes run. There is no indicator of what is wrong, no error code just die and won't restart until it cool down. I notice that the fa… Read More
I have a 2021 colman 400utv engine will start and idle, as soon as you hit throttle to move engine dies and will only start when you throttle it, let off throttle it dies, I replaced the inj… Read More
Purchased a 2011 bighorn banchee. Needs motor work. Not sure what. Husband is mechanic but not computer savvy. So, is there a manual that will tell him how to tear this down? We have down l… Read More
I am beginning to wonder if anyone has had good results from the Chinese crap (Hison, Massimo, Axis, Odes and others) mostly coming out of Texas. By good results I mean a good reliable two… Read More
I purchased a new 2023 Landmaster UTV L4 in October of 2023. UTV didn't seem to have as much power of the demo L4 that I drove but figured once it broke in it would be better. After about… Read More
2016, Hisun 500 turns over great but Spark plug is firing when I turn the ignition key on. I’ve got good fuel pressure to the injector. Pulled plug out and it is wet with. gasoline. Ai… Read More
after looking at the diagnostic procedures in this forum, I am finding my Gunner 250 does not have an engine warning light on the dash. i have tried to see if any other symbols flash, but no… Read More
I am looking to replace the fuel injector on my Bennche Bighorn 400. It calls for part #16400-003C-0000, but the fuel injector part #16400-004C-0000 is much cheaper. Are they compatible?… Read More
Hi to all. I’m new on this forum and I need some help. I have a 2008 arctic cat 700 xtx prowler. I have no spark.
I have done the following repairs.
changed piston and cylinder… Read More
View File
2018 HISUN HS-550 Sector Rural King Manuals
This is the Service manual, Parts manual, Owners manual, plus much more for my 2018 HS-550 RK UTV Side-b… Read More
My UTV is a few years old and gets very little use. I just noticed the drive belt slapping the plastic guard and making some noise. The manual tells me how to replace it but not how to tig… Read More
I have a 3500LB Winch that only runs in one direction. Inward but not Out. Replaced the solenoid module. Makes "click" when I push the "Out" button and the motor tries to spool out but t… Read More
Don’t waste your time everybody with rpm motorsports, Omaha. They are people that don’t even work on sxs’s. Trying to tell you how to install things.
Completely uneducate… Read More
I have been looking to outfit my new Polaris xp 1000 but have been finding prices all over the range for the same item. So I thought it would be good idea if we could all share here where yo… Read More
I'm working on a Coleman UTV 400 that has a rough idle, owner has had it for about a year. When I say it has a rough idle, it doesn't have the continuous smooth running sound. At times you c… Read More
Since it is a royal pain to close the front hood, I went to add a charger wire so I don't have to worry about the hood, I found the screw on the positive post rusted . this utv is 11 month… Read More
hello everyone, i just joined this forum to try my luck, few days ago i bought an old (dont know exactly), 2011/14 hi sun 500cc ""carburated"", was not running at the time, but i fell was a… Read More
I am trying to locate a transmission radiator for my 2022 coleman UT400. I cannot find a parts listing that shows the transmission radiator, so I am not sure what the part number is Read More
i just purchased a 2024 g2 z force 800 and would like to power some accessories with out hardwiring would a 3 way cig lighter adapter work plugged into the 12 volt outlet on the machine each… Read More
I have a 2022 500 Hisun product, I have had them in the past. I change my oil myself and trying to drain through the hole where I remove the plug is a mess. How does everyone keep the belly… Read More
Hello!
I am a University of Notre Dame student and have been enlisted by Lippert Components INC. to help them understand you, Side-by-side users. Taking the survey in the link below… Read More
does any one else have a slipping belt on the hisun ...i put new wet clutch one way bearing new belt, cleaned primary and secondary and still get slight slippage Read More
I’m getting a 700-7 every startup. I’m having to change the plug every 100 miles on 93 octane gas. I got a lower numbered plug that is supposed to burn hotter. I’m wonderin… Read More
I bought a 2013 Cub Cadet Volunteer 37BM466D710. It has a LH775 engine in it. Now my issue is I bought it off an online auction and well I got took really hard. There is no CVT/transmission… Read More
Hello, new Hisun Axis 500 owner here. I have a 2020 in the Mountains of North Carolina. It runs fine and I enjoy it but it seems to struggle on the hills. Granted I have one that is pretty s… Read More
View File
MSU 500-700 Wiring Diagram
THis is the wiring diagram for MSU500 through MSU700. It looks to be right and I have verified most of it by hand… Read More
I have a 2012 Massimo MSU 500 that died. I found that it didn't have spark and the fuel pump wouldn't run. Checked all fuses and none were blown.
Went through and replaced the ignition… Read More
Less than 40 miles can barely start. Dealer is working with Hisun on a number of other issues on this UTV. Can not get clear info on the meaning of these E codes this is getting. Anybody hav… Read More
I just picked up a 2009 bmx utv 500, there is a small 'nipple' on the water pump, its barbed like a hose goes on it , where is that little hose Suposed to go? Read More
I just picked up a 2009 bmx utv 500, there is a small 'nipple' on the water pump, its barbed like a hose goes on it , where is that little hose Suposed to go? Read More
So I've got a Hisun 550 that I was doing some work on that required removing the CVT and it's housing. Upon attempting to reinstall the clutch, sheaves, etc, I found that the belt no longer… Read More
Hello Everyone, COOL NEW Product Alert! A company called NEW Wire Marine or NEW Wire has Badass custom panels for UTV, Buggy/Hunting trucks. From Fully wired switch panels with laser etched… Read More
I have recently purchased a Land Master LM300, with the Kholer engine (277). When purchased from a private owner he said it was a 2015?
I guess I could take his word for it, but nowher… Read More
I installed a new GY6 150cc engine in a Bull Dog Pup 200 and when I put it in drive, it grinds for a second and then runs fine. Works great when i place it in reverse. Could it be from it… Read More
We own a 2020 Kubota RTV-XG-850, with only 400 hours on it and it has been at the dealer 3+ months. We were just informed our engine failed and requires a complete rebuild at only 400 hours!… Read More
Got a new 2023 TBoss 560 with 40 miles on it now. Noticed after about and hour of plowing snow coolant started hissing out the overflow tube. Initially made a pop or blow kind of noise and t… Read More
Please help I have a Massimo 400 buck that has an oil leak. The oil is leaking on the front side of the motor. It leaks out of a u-shaped steel pipe that has two banjo style fittings on it… Read More
Good afternoon.
im in the market for doors for my ranger/ rzr sxs. I’m finding lower doors, but what I’d really want is full doors so I don’t have to unzip when exiting… Read More
I've had a battery failure and need one replacement. The local distributor told me it might take up to four weeks to get one. I'd like to order one in sooner than that if possible. Any he… Read More
Where does an Axis 500 receive power from? Is there a relay from the ignition switch or is the pump controlled by the ECM? Asking for some folks that are having issues that seem to be a los… Read More
I have a Gator 550 UTV with two rows of seats and dump bed. I bought new LED lights for front and back and have mounted them on the roof, no problem
I now need help hooking and running wir… Read More
2020 Massimo Buck 400 - Won't start. Can hear the starter spinning, but motor never turns. Relay? Starter? Worked fine one day and not the next. Thanks for any help you can provide Read More
Hello guys!! I just joined the forum so there are so many things I don't know yet, I hope to have the help of the boards, and I really want to get to know you all on the forum Read More
Hi
The EFI light starting flashing (fast, every second) on my ‘21’ zforce 500. Still starts and runs fine. Pump still kicks on strong when starting. Battery is nice and stro… Read More