The Washing Machine Drain hose is an integral component of the washing machine. It helps get rid of the dirty water left over from doing laundry. 

Generally, when someone buys a washing machine, they do not check the outlet or understand how to maintain the Drain Hose system. Keeping the washing Machine Drain Hose clear will allow you to be more efficient with your laundry and reduce stress from the washing machine itself.

This article will clear a few crucial doubts about the washing machine drain hose. So, sit back, relax, and read through.

Connecting The Washing Machine Drain Hose with a Drainage Pipe

Whenever you buy a new washing machine or relocate an old one, you must connect it to a water supply and a wastewater drainage system.

To attach the drain hose, you’ll need a standpipe or a washing sink. If there isn’t a standpipe or sink, you can create one using a PVC pipe. 

How Should you connect the hose?

You will need to go over a few steps before successfully connecting a washing machine drain hose. Let’s go over these steps to understand how to get it done. 

Step 1

After you’ve installed the water supply hoses, replace the washer. Most drain pipes usually come preinstalled with washers. 

Connect the hose to the machine’s drainage aperture if your washer does not come with include a drain hose.

Measure the shutoff valve or the sink’s elevation. The edge must be at least 30 inches off the ground.

Step 2

To prevent water from being sucked out of the washer, plumbing rules require an air gap left between the washing machine drain hose and standpipe. 

Link the drain hose to the standpipe or laundry sink’s lip. When connecting to a standpipe, leave the hose un-sealed.

Do not let the hose touch the floor. Keeping the hose elevated will quickly drain the water from your washer as you fill it. 

Connect the machine to the power source and run it through an entire cycle to ensure it drains properly.

Step 3

Construct a 12-inch PVC pipe standpipe (if your laundry room has a floor drain and no sink or standpipe), then cut a 35-inch-long piece of PVC pipe. Note that this section should be upright.

Determine the location of the vertical pipe on the wall. On the lower end of the vertical tube, cement a 90-degree elbow. Cut a second piece of the PVC pipe to extend the length of the upright so that it can reach the floor drain.

Attach another 90-degree elbow to one end of this horizontal pipe, pointing it into the floor drain. Conclude by connecting the washer drain line to the upright’s lip, and your washing machine drain hose is connected.

Can You Fix a Washing Machine Drain Hose?

The straightforward answer to this question would be a yes. But, there is a catch. If there is a mart near your house with washing machine accessories, putting in the effort to patch up a torn drain hose is honestly a waste of time. 

It is much better and safer to buy a new set because a new groove will cost you just around 20 dollars and eliminate the dangers of having to work with heavy tools. 

When it is impossible to avoid replacing a damaged sleeve, we take a different route. Sometimes, the only option for damage control is temporarily sealing the washing machine’s drain hose.

How to Seal the Washing Machine Drain Hose?

You will find several methods to repair a washing machine’s drain hose on the internet. Still, not all of them are genuinely reliable. Amateur craftsmen frequently recommend a straightforward solution: sealing the break using duct tape. 

You must wrap the hole itself and 10 cm on both sides, in numerous layers, without skimping on the adhesive tape.

Neither is it possible to determine the reliability nor recommend the tape technique: it’s entirely dependent on the size of the damage, quality of the tape, and effort put in to fix it. 

Professional plumbers provide a more durable and reliable option of manually inserting a plastic tube into a ruptured hose to tackle the problem.

Here are a few steps you can follow:

• Attach two metal clamps and a pipe (the latter should have a length of 8 cm and a diameter proportional to the drain hose).
• Find a crack in the groove.
• Trim the sleeve in the impaired area, opening access to the “interiors” of the pipe but do not cut it completely.
• Properly lubricate the prepared tube with a waterproof adhesive.
• Insert the line first into one half of the groove, then into the other (the cut should be in the middle).
• Touch the hose and locate both ends of the inserted tube.
• Secure the clamps at both ends of the line over the hose.

Using this method to repair the washing machine drain hose will ensure that the patching lasts for a considerable period. Water emptied from the machinery will flow via the newly added tube, avoiding the damaged area. 

The only apparent “disadvantage” here? The part between the hooks is rigid.

How to Clean a Washing Machine Drain Hose?

Soap residues, dryer lint detritus, and dirty clothes can all cause blockages in your washing machine drain hose. Here is a helpful method to remedy the problem at home. 

Vinegar and Baking Soda solution all the way

You will require the following ingredients: baking soda, vinegar, and boiling water. This trio is a safe way to unclog your washing machine drain hose at home. 

Access the drain pipe and fill a bucket halfway with hot water, vinegar, and baking soda. 

Pour the liquid slowly down the drainpipe, allowing time to react with the blockage.

Utilize a funnel if required to avoid creating a mess. Pour the liquid down the drainage pipe until you are sure the clog has been dissolved or pushed out.

Conclusion

After having discussed so many things about the washing machine drain hose, it is safe to say that you guys have enough intel to keep your drain hose healthy.

If you doubt that the damage is beyond repair, it is always best to seek professional advice.  

The post Here’s What you Need to Know About a Washing Machine Drain Hose first appeared on Take Care Of Your Clothes.