People normally tend to Turn off the heaters in the summer season to save electricity and fuel. But during the winter season, heaters are needed to keep your house and yourself warm and comfortable. So you should prepare your Heater to turn on during the winter season.
Do you have a Gas Heater in your home? Are you looking for ways how to turn on gas heater? In that case, you have come to the right place. In this article, we have tried to introduce some steps which will help you to turn your gas heater.
Step 1: Turn on Preparation
- Examine the heater’s operating directions:
How to turn on gas heater is an important question. But before knowing how to connect gas heater you need to examine the heater’s operating direction. The basic operational instructions are generally written on the sticker which is attached to the access panel. The wrong operation method of your gas heater can lead to fires, explosions, property damage, personal injury, or death.
In some heaters, there might be no sticker attacked on them with the instructions. In this case, you should read the manual that comes with the instructions. By any chance, if you can’t find the manual you can look for the instructions online by mentioning your heater name with its model number. This will ensure that you will find proper instructions for your gas heater.
- Check for gas and water in the area around your heater:
Try to smell the area around your heater, especially the floor. Some gas is heavier than the air and for that reason, they might sink to the floor. No water and gas leakage should be allowed near the heater. Water can cause heavy damage to your heater.
If you notice the presence of gas don’t let anyone turn on light switches or phones. Leave the building as soon as possible and call the gas company for further procedures. In case of leakage, turn off the contact of your heater with the electricity and then repair those leaking pipes. Now dry the pipes completely and then turn on the electricity contact of your heater.
In case of the submerging of the heater’s electrical components with water stay away from turning on the heater. Contact a technician for inspection and to replace the destroyed parts.
- If necessary, provide power to the heater:
When your heater has been off during the summer days you need to restore power to the heater at the electrical panel of your home. You may find these in your basement, utility room, or garage. The heater’s fuse must be in the on position.
- Remove the front side of the heater’s access panel:
The front side of the access panel is normally tied with the screws. Untight them with a screwdriver and keep the panel to the side. Removing the access panel helps you to have an improved vision of the pilot light. Controls such as gas supply can be found behind the panel.
Step 2: Lighting and Adjusting the Pilot
- If your pilot is lighted, inspect the flame:
The brief of the proper flame for your pilot should be mentioned in the manual. The flame shouldn’t be excessive yellow and also should be separated into two or more flames.
- If required, adjust the pilot light:
In the case of most pilot lights, you can adjust them by adjusting a screw on the body of the pilot valve. While handling the access panel, insert a required screwdriver into the slot of the pilot screw. To make the flame more intensive turn it counterclockwise.
Look for the pilot adjustment screw in the heater’s manual before adjusting it. Turing the wrong screw can impact your pilot’s performance negatively. Differences can be noticed in the ideal pilot light for different types of heaters. Most home heaters have a full and steady flame between 1½ and 2 in tall.
- Purge the heater of any unlit pilots:
Turn off the heater’s switch. The gas supply might be found in the heater’s bottom, in its control panel, or inside the access panel. After turning off the gas supply wait for five minutes. If you don’t wait for at least five minutes can lead to improper dissipation of the gas which can lead to fire problems while relighting the pilot. While the gas is dissipating find the reset button for your heater and you will find it around the gas supply controls
- Using a long stem lighter, light non-auto igniter pilots:
Take a long stem lighter and hold it with your hand. Then set the supply gas to pilot. Ignite the lighter and then press and hold the reset button. To open the pilot light bring the lighter’s flame.
Release the reset button and turn on the gas supply. Take a long stem match instead of a long stem lighter. Roll the paper into a thin tube and light one end with fire. You might need to re-perform the pilot lighting procedure several times.
- Wait for the heater to turn on before using an auto igniter to start the pilots:
In your heater’s instructions if it’s mentioned that the heater has an auto igniter then don’ try to ignite the pilot with your hands. Different models have different procedures for lighting, so follow the instructions mentioned in the manual. Heaters with auto igniters should normally be turned off and purged of gas. The access panel should be replaced and the heater’s power should be restored.
Step 3: Turning on the Heater
- Reattach the access panel if necessary:
Reattach the access panel in place on the heater. Use a screwdriver to reattach the panel in place. If the access panel and door covers aren’t reattached properly then it can prevent your heater from starting.
- Turn on the heater:
The “On” switch of the most heater is placed at eye level of a little bit higher. The switch is generally installed near the bottom of the basement stairs. It might also be found in the heater room. Turn on that switch.
- Set the thermostat:
How to turn on heater in house thermostat is a crucial question. To know the answer to this question you need to set the thermostat properly. After turning on the heater the thermostat of your heater should have power. Choose the heat setting of the thermostat and set the temperature of your comfort.
When the temperature will drop below the thermostat setting the heater will turn on. If your heater has an auto-ignition feature, then you need to trigger the igniter with a special thermostat setting. It is sometimes labeled as “Call for Heat”
Step 4: Troubleshooting Your Heater
- Replace any damaged heater filters:
Dirty filters are the basic problems that prevent your heater from starting. Buy a new filter and replace it with the old filter. Before doing so make sure to turn off your heater. Always follow the instructions mentioned in the manual for best outcomes.
- Examine the thermostat’s settings:
Ensure that the thermostat is working properly by adjusting its temperature setting by increasing it to 5 degrees until the heater turns on. Make sure that the “ Heat” setting is selected on the thermostat. If the thermostat is broken then call a professional to replace it.
- Examine any doors, coverings, or registers:
If access panels and doors aren’t reattached properly many heaters will not turn on. If there are too many heat registers then you can face problems. 20% of the heat registers should be closed.
For example, if you have 10 heat registers in your home then you must need to close only 2 registers. If you close the register in any unused rooms then heating costs can be reduced.
Safety Precautions
As mentioned before your gas heater has a thermostat. The thermostat works along with the pilot to lit it. It runs from the pilot to the main gas supply. The thermostat around the pilot heats up and sends electrical voltage to the gas valve.
The gas supply is kept open by this voltage. The electricity supply ends if the pilot light goes out, closing the main gas valve.
Frequently Asked Questions (FAQ)
1. Are gas heaters inherently dangerous?
Answer: Some gas heaters may achieve extraordinarily high temperatures of 600 degrees Fahrenheit (315 degrees Celsius). If they come into contact with any household products, they might cause fires and shock dangers, especially for children and pets. However, they are far safer than typical portable heaters in the end.
2. Is it possible for a gas heater to catch fire?
Answer: Even if there are no open flames, flammable oils, or gasses, gas heaters can create a fire in your home. When utilizing a gas heater, one of the most serious dangers is a fire. As a result, you should always be cautious when using any kind of heater in your home.
Final Words
The gas heater’s popularity is increasing day by day. These kinds of heaters are easy to install and very simple to use. Turning on a gas heater isn’t a big deal. We hope that by following the steps mentioned in this article you will learn how to turn on gas heater.
The post How To Turn On Gas Heater – 4 Easy Steps appeared first on HomeNar.
