- An Electric Chain hoist is a electric equipment in which the high capacity Alloy Steel Chain is used as a lifitng element to lift the material or object vertically up or down.
- Electric Chain Hoist is used as a stand alone equipment, used in the overhead crane or jib crane or in goliath crane.
- LOADMATE Chain Hoists is ideal solutions for different kind of workstation.
- Electric Chain hoist is preferred over Electric Wire Rope hoist in several cases based on the application.
- Before operating Electric Chain hoist, main component such as brake, switchgears, clutch, remote, hook must be checked well.
- Under the normal working condition, the vertical lifting and descending and horizontal movement of electric chain hoist is controlled by pendant push button.
- There will be some risk when electric chain hoist works with heavy load, especially when it is not properly operated or poorly maintained.
- Due to potential serious accidents and casualties, do remember that safety always comes first when you are operating, maintaining or checking euro serial electric chain hoist.
- Do not use the hoist to lift, support or carry persons.
- Do not operate it close to/over persons.
- Do not lift more than rated load marked on the name plate of electric chain hoist.
- Always remind the persons nearby of safety before lifting load.
- Always read carefully safety instructions.
- Do remember that it is and operator`s responsibility to make correct installation and operation. For more documents of safety operation of the hoist, please refer to all relevant safety regulations and other laws. Read more:
- Electric chain hoist characteristics motor brake, hook and hook latch, limit switch, friction clutch. Read more:
- Do remember that only trained personnel should operate the hoist.
- Before using the hoist, ensure to check it according to “aily exam” requirements.
- Ensure that chain is long enough.
- Always check if hook latch can normally work, if not replace the missing one or the damaged one.
- Always check brake before using the hoist.
- Whenever two hoists must be used to lift load, ensure that load capacities of the two hoists must be more than/equal to the load.
- Ensure to use original chain or the chain authorized by manufacturer.
- Do check and keep the lubrication of load chain surface.
- Do not use electric chain hoist without name plate.
- Do not use modified or distorted hook.
- Do not use electric chain hoist in the explosive environment.
- Make sure that load correctly lies in the hook.
- Ensure to tighten chain and load sling when starting to lift load. Do not suddenly add load.
- Do not operated the chain too slowly.
- Do not reverse motor hoist before it has completely stopped working.
- Make sure that the hoist is in service life and operate it within rated load and ED.
- Ensure to operate it after making load center of gravity right underneath the hoist.
- Do not use hoist chain as a load sling.
- Do not use a distorted, twisted or extended load chain.
- Do not shake suspending load.
- Do not support the load with hook tip.
- Do not scrape some sharp edge with load chain.
- Do not weld or cut the suspending load.
- Do not use the hoist chain as a welding electrode.
- Do not operate the hoist when the chain jumps or makes much noise.
- Do not use inverted load chain.
- Don not frequently use friction clutch and limit switch, otherwise the hoist will be seriously damaged and can cause harm to the surroundings.
- Do not forcefully push the button cord.
- Choosing chain container
- Chain container is used for containing load chain when the load is lifted.
- Check whether the stopper is correctly fixed on the third link starting from the no-load side chain.
- The stopper with upper limit switch should be fixed on the sixth link of the load side. The stopper with upper/lower switch should be fixed on the eighth link.
- Chain can not be distorted or twisted when it is sent from the free end to chain container, otherwise it many touch limit switch and stop the hoist falling.
- In addition each chain container tells the maximum length of load chain that it can hold.
- It is dangerous to use a chain container which cannot hold the load chain. Only when all load chain is put into the chain container , limit switch can normally work.
- So it is important to make sure of load chain length before its container is decided.
- Lubricating gear case
- Lubricating load chain
- Checking chain alignment
- Checking cables and working voltage
- Installing chain hoist with trolley then must be five item refer like chain container, lubricating gear case, load chain , chain alignment, install trolley.
- Chain hoist connect with chain container, cushion rubber, stopper, chain container suspender, socket bolt, lever nut, chain container spring, plain washer. Read more:
- Do not go away when the load is still being suspended and or leave it hanging too long.
- Electric chain hoist Operation test in different kind of test like lifting test, Traversing Test, Limit Switch Test, Lifting & Falling Brake Test, Emergency Stop Button Test.
- After Hoist packed unboxed first proper check parts match with invoice or instruction manual.
- All proper checking electric chain hoist connect with trolley proper, trolley join with beam, bolt-nut-split pin proper tight.
- Lifting test is push button press and check travelling direction. Limit switch test in upper limit and lower limit switch.
- Lifting brake test button release then stop at time motor. When push emergency stop button then check hook is stop or not. Read more:
- Make sure that it is professional technicians who have a routine check of the electric chain hoist. Electric chain hoist maintenance activity must be note down specific time period.
- Always off power when hoist in repair. After repair hoist must be test load before the main operation.
- Replace oil gear at least five years even if hoist not use minimum worked hours. If you can use light load then after 360hrs change gear oil , moderate load in 240hrs, heavy loads 120hrs.
- Always keep load chain in lubrication
- Do not extend load chain by connecting, adding or welding.
- Do not touch the electrified components.
- Do not adjust friction clutch.
- Breakdown is failure, machine stop working.Hoist Breakdown give negative impact on production or manufacturer cycle.
- Breakdown is highest chance generate automatically. But if you can point not down some step follow then 85% less chances to Breakdown Generate during working time.
- Electric chain hoist breakdown exclusion must be need to troubleshoot fast and make the hoist working again safely.
- Some of the basic breakdown exclusion is electric cable shock, not motor movable, hoist can`t stop, hoist can`t lift load, lubrication oil leaks, load chain noise generate and much more… Read more:
Expected Goal:
Preparations:
Instructions for safe use
Characteristics
Pre-Operation Preparations and Examinations
During-operation Regulations
Installation of Electric Chain Hoist – hook suspension
Installing Electric Chain Hoist & Motorized Trolley
Operation Test
Maintenance
Breakdown Exclusion:
The post Manual Instructions Guide For Electric Chain Hoist appeared first on EOT Cranes Manufacturer | Electric Chain Hoist | Hazira - Surat, India.
This post first appeared on The Lifting Equipment Specialist - Loadmate, please read the originial post: here