It’s an exciting experience when you know how to fix a Leaky Moen Kitchen faucet, right?
The day is not so far when you are capable of solving this problem alone with your knowledge. The aim of this article is to make you confident enough to handle this DIY project without any hassle.
It is very easy to do. Also, it never cuts off your valuable time. You can treat the blockage. Or you can replace some of its parts as well.
See in video how to fix leaky moen kitchen Faucet
In most cases, it depends on what types of faucets you are using. In this article, I am going to share more actionable ideas to sort out this issue with an efficient hand.
Methods of Repairing leaky kitchen Faucet
There are some following steps you should follow to get back it to the previous one. Here is the process of how to fix a leaky moen kitchen faucet.
Find out the defective spot
This one is probably very tough to detect. I am telling so because you are able to see the drip. It’s difficult to understand from where it starts dripping.
Before you start repairing, you need to inspect where it has defect. In general, it grows from the base or from the spout. You need to find out it carefully.
If you find out that faulty area, soon you can apprehend what parts you require to fix it.
Stop The Water Supply
Check the sink first of all. Make sure the water is not flowing anyhow. If it so, turn it off with the attached pair of valves. If the valves are missing, go for closing main water line.
Make sure you stop its supply properly. To do so, you can take the faucet apart from the sink.
Doing so will help drain away the water pressure and ensure about stopping the constant flow.
Open the leaky faucet carefully
In this step, you will have to put out the faucet taking it on the center position. This will make it get relief from unwater water pressure. Then use a towel or any old newspaper to cover the whole sink perfectly.
This step is very crucial to do. It’s not at all a funny thing to drop any small equipment’s down the basin. To save these materials from falling out in the sink, you must do it.
Record the whole process
This is very important to remember each and every step of fixing the faulty area. When you will finish repairing it, you need to join the parts in order.
To reap the best benefits, turn on your camera and make a video recording. By doing so, you can recall when and where to fit the right components.
Wash the components with vinegar
Minerals have chances to build up on the every parts of the faucet for random usage. That’s why it needs to get washed.
Take some vinegar and let the parts soak in it. Let it remain like this for couple of minutes. This will make the spills loosen quickly. And you can clean them with a scrub.
To scrap away any strong debris from hard to reach area, you can use a screwdriver. This will benefit you a lot.
Remove the handle Carefully
You must lift the handle in this step. The best way to do so is to use an Allen wrench. First of all, find out a small hole below it. Then use this tool and move the ultimate screw anticlockwise.
Later, detach the ball valve and other little equipment’s in order. Keep them safely so that it wouldn’t get lost in any way.
Tighten the ring carefully
First of all, hold the peak point of the metal cap carefully. Use a spanner tool to do so. You must turn it from clockwise. For the handle’s base repairing, this will complete most of the work.
Remove the cap
Holding the top part of the cap, you must remove the cap properly. In this case, use slip-joint pilers. Turn it around from anti-clockwise.
Carefully take them aside. Then you will find the 2 plastic rings. Thisequipment’s are helpful if you want to expose the ball.
Check the metal ball
If you find something defective on the metal ball, replacing will be the best way to fix it. Take the ball in your hand. Check properly it is not cracked at all. The make a good replacement with a new one.
Rubber Ring replacement
With a screwdriver, you can make an easy transformation of the rubber rings. Inside the ultimate holes of the faucet, keep the new springs.
Assemble the faucet in order
Can you remember you made a video recording when detaching the faucet? You must check the components carefully and join them one by one by watching the video.
Consequently, you must do it correctly. Join the faucet again. Check it by resuming the water supply.
Why you need to fix the kitchen faucet
- It will save your extra cost. When you are ready to seek the mechanics help, you should be ready to fill his pocket. If you can fix it alone, this is very helpful for you economically.
- If you are callous to repair it immediately, it may be the reason for water damage.
- The leaky kitchen faucet will result unlimited dripping. That’s Why it’s better to solve it urgently.
- Constant dripping will make increased amount of water bill. Fixing it will be a wise decision for you.
Final Words on moen kitchen Faucet
Finally we have come to the end of the article. In fact, knowing about how to fix a leaky moen kitchen faucet will help you a lot. It’s not that hard enough to do. It’s just an easy and simple task.
Repairing the faucet will save a good percentage of the electricity bill. I truly hope you can do it nicely without any hassle.
The post How To Fix a leaky Moen kitchen Faucet- Fix kitchen Faucet appeared first on Elite Rice Cooker Guide and Reviews.
