Thanks for joining me for twice the fun this week! The beautiful and new line of fabric, Mary, of Banyan Batiks, is in stores this month! In yesterday’s post, I created churn dash blocks to make a second quilted cushion from the leftover fabrics from the first cushion cover this week.
The beauty of the separate batiks was being challenged setting the blocks beside each other so today we’ll add a sashing between them before quilting and creating the Cushion cover.
Before we add sashing, make sure each of your Churn Dash Blocks is 9½” square.
Then use the Ketan batik Light Cinnamon (81000-370) cutting it into 2 – 2″ strips. Subcut one into 2 – 9½” strips and one into a 20″ strip.
Sew one of the 9½” strips to the right side of the top left Churn Dash block; press the seam to the strip.
Sew the top right churn dash to the other side of the strip, pressing the seam to the strip.
Repeat with the bottom two churns and the remaining 9½” strip.
Sew the 20″ to the bottom edge of the top row; press the seam to the strip.
Sew the top edge of the bottom row to the strip, pressing the seam again to the strip. See the photo below.
The cushion top should measure 20″ square.
Quilt cushion front
Layer the cushion front backing fat quarter Right Side Down on a flat pinning surface.
Place the batting on top.
Place the assembled cushion top on top Right Side UP.
Pin the layers together or use your preferred basting method.
Use a contrasting thread to quilt. I quilted ¼” away from the Fabric B/D churn dashes and in the ditch of the Fabric A/C churns. I also quilted in the ditch of the sashing.
Trim the quilted pillow front to 20″ square remembering to keep a ¼” of fabric past the churn dash points.
Prepare Back Panels
The top back panel is made up of leftovers from Fabric F and coordinating Ketan batik Chestnut Orange. Sew them together to make a panel 20″ wide x 15½” high. Be sure to zigzag the seam between the fabrics.
The bottom panel is made from the coordinating Ketan batik (81000-370) used for the sashing cut 20″ wide x 8½” high.
Hem along one long edge of each panel:
press ¼” of fabric over to the wrong side and then another ¼” and sew using thread that blends in with the fabric colors.
Sandwich and Assemble Cushion cover
Lay your cushion parts on top of each other in this order on your pinning
surface:
- Place the cushion cover front, RIGHT SIDE UP.
- Put the back top panel, RIGHT SIDE DOWN with the non-hemmed edge lined up with the top edge of the cushion cover front.
- Line up the back bottom panel, RIGHT SIDE DOWN, with the non-hemmed edge lined up with the bottom edge of the cushion cover front: the hemmed edge will lay over top of the top back panel hemmed edge.
Pin all the way around the outside of the cushion cover: be sure to pin at the sides where all three layers overlap.
Sew ¼” all the way around the edges of the cushion cover.
Check to make sure you have sewn through all the layers.
Serge or zigzag stitch to finish seams.
Two quilted cushion covers done! Turn this second one out, pushing the corners out with a fingertip and insert a pillow.
The backs of the cushions look great together thanks to the coordinating Ketan batiks and the prints in the Rust colorway of Mary.
I hope you enjoyed the design possibilities of the churn dash block this week. The Banyan Batiks, Mary line was fun to use creating different coloring options for the design. You can’t go wrong with these prints! I plan on having fun with batiks all summer long
This is part 5 of 5 in this series.
Go back to part 4: Making a dashing Mary Batik churn dash cushion cover
The post 4 quilted churn dash blocks are better than 1! appeared first on QUILTsocial.
This post first appeared on QUILTsocial - Eat, Sleep, QUILT, Repeat, please read the originial post: here