Anker’s Ultra Slim Extended Battery Case provides the best mixture of good performance, price for the capacity, and physical size (the quantity of bulk it boosts the phone). It offers the capacity to deliver 117 percent of a full charge with an Iphone 6 or 108 percent with an iPhone 6s. The cost tag, $40 at the writing, is crazy low for a battery case: In that rate, the Ultra Slim provides the best charge value (a 2.9 percent charge per dollar, or $34.34 for the full charge, for that iPhone 6) of the cases we tested, undoubtedly.
The Ultra Slim doesn’t have an especially premium feel. That’s not to say which it comes off as cheap, but nothing about its physical construction is extremely impressive close to other cases. Another minor strike against this Anker case is its insufficient button coverage; we almost always prefer (well-designed) press-through button covers that protect the iPhone’s various buttons and reduce the volume of places where dust and dirt will get underneath the iphone6 case supplier.
For your iPhone 6 Plus and 6s Plus
Anker doesn’t make an Ultra Slim for the iPhone 6 Plus or 6s Plus, so for those handsets, we love to the Tylt Energi Sliding Power Case. Unlike most of the models we tested, this one features a separate protective case that one could slide out of your battery sled once you don’t need the extra power, rendering it a more-practical selection for the already huge Plus models. It’s yet another great power source, providing on average a 93 percent charge for the iPhone 6s Also in our tests.
A significant thing to remember together with the cases we dismiss below is simply because they are certainly not necessarily bad. Although we’re noting any issues we saw with one of these cases, some of them are fine-they just can’t quite match towards the high quality in our picks.
Our previous pick for any more protective case was Speck’s CandyShell. A perennial favorite, it provides two layers of material-Plastic externally, rubber internally-that provide more protection than case designs that happen to be just one or maybe the other. The CandyShell is 10.9 mm thick, which puts it about the chunky side, but it really doesn’t feel exceptionally bulky, and it’s one in the only cases we tested that claim to satisfy military drop-test standards. Speck supplies the case in a wide range of colors, and variants add rubbery grips (CandyShell Grip), credit card holders (CandyShell Card), and graphic prints (CandyShell Inked).
The CandyShell has a few things that keep it from as a top pick, though. To begin with, the CandyShell’s glossy back quickly attracts small scratches that generally aren’t visible directly but jump out when you see the iPhone in an angle. Granted, these scratches don’t modify the protection the truth offers-and we’re naturally happier to discover scratches about the case as an alternative to in the phone itself-but it might be nice if Speck were to offer the case having a matte finish.
Other dilemma is the case’s shape. Some of our readers, together with a contingent of Amazon reviewers, take trouble with the fact that the CandyShell’s back is slightly convex. Specifically, if you set the situation on a flat surface, this “hump” causes the way it is to rock once you press along any kind of its edges, or perhaps to spin such as a top in the event you push it. (Should you purchased a CandyShell and also you mind this spinning and rocking, Speck says to contact its support service department.)
OnePlus (the Android phone maker) surprisingly decided to get in around the iPhone-case game featuring its Sandstone Case. The important draw is OnePlus’s Sandstone texture; TIME says that it “feels like smooth sandpaper” and this “[i]t’s super grippy, rendering it hard to drop.” Unfortunately the way it is is a shell with open top and bottom edges, meaning it’s less protective when compared to a good case needs to be. As a result design drawback, it fell away from competition.
SwitchEasy includes a mixed history, one which make it challenging to tell the full story according to its cases alone. Its Numbers case was our original pick to the iPhone 5 and 5s, before a wave of reader complaints about quality and customer support. The answers we got from SwitchEasy weren’t thorough; mostly, the business blamed the difficulties on third-parties selling knockoffs of their products. (At iLounge, I found the SwitchEasy protectors to be impressive generally speaking-the Numbers earned a rare A rating from me-but readers there contacted me about similar issues.) Ultimately, we pulled our recommendation.
With all that under consideration, we looked at three SwitchEasy cases for that iPhone 6. First is the Odyssey. Like a number of the better cases we’ve evaluated, it’s a mix of plastic and rubber. Rather than being layered, the type of material run side-by-side, with the hardened rubber making up many of the case. It isn’t the prettiest case, inside our opinion, but it is protective. It covers the buttons without reducing much of their clickiness, and six holes along the conclusion up precisely with the speaker vents. The most popular section of the case may be the port protection: Rubber protectors squeeze into the headphone and Lightning ports, respectively, when they’re not in use, keeping dust and other debris out.
SwitchEasy’s Tones includes exactly the same port protection and uses exactly the same materials. Your body is usually plastic, though, together with the rubber walking around the edges being a border in addition to across the rear of the truth, matching the iPhone’s antenna lines. We’d prefer a layer of rubber between the handset and the plastic back from the TPU iphone6 case, and also the Sleep/Wake button requires a bit too much pressure about the handful of units we tested.
Our initial impressions of SwitchEasy’s Numbers were very positive-we had been prepared to name it as being our top pick-but there’s a lot more towards the story than just our review units, and we found a significant fault after some extended use. This case is nearly just like the Incipio NGP, nevertheless it provides more protection. As opposed to leaving the phone’s ports totally exposed, the truth provides protectors that suit to the headphone-jack and Lightning-port openings to hold dust and debris out. It’s a great touch that’s executed well. Even the phone’s speaker is way better protected, with six individual holes as an alternative to one long opening. We actually such as the tactility of your devqpky94 a bit more with SwitchEasy’s model than with Incipio’s case, too. A young yellow version of the case we tested accumulated permanent stains, but later iterations exhibited no such issue. The problem is that the case is too loose, so the corners appear too easily. We experienced this concern over and over while eliminating the encased phone from our pockets. Because we’ve had other issues with SwitchEasy cases in past times, we’re still a little wary. If you opt to purchase a SwitchEasy case, we recommend buying it directly from the company’s website. Doing so will eliminate any potential warranty difficulties with third-party sellers, should you have any difficulties with the situation.
A vital thing to not forget with the cases we dismiss below is the fact, unlike along with other groups of products we cover, they are certainly not necessarily bad. Although we’re noting any issues we saw by using these cases, a few of them are fine-they merely can’t quite match on the premium quality of the picks.
Combining a rubber skin having a plastic frame, the Spigen Neo Hybrid can be a slim, attractive case. Its fatal flaw is based on its button protection. The silver plastic pill across the Sleep/Wake button doesn’t depress properly, so it may possibly not hit the control underneath, and you likely won’t feel it whether it does. Former Sweethome editor Joel Johnson confirmed this issue with the iPhone 6 Plus version. Because we received this case for testing so early, we think Spigen might revise later editions to handle this issue.
Also from Spigen may be the Ultra Hybrid, one particular-piece case that fuses a rubber frame with a clear plastic back. It’s a nice-looking case, but when again, it has problems with the buttons. Rather than putting raised material over them, it offers left and right edges that happen to be flat all the way through with small indentations. To the Sleep/Wake button, the indented label says “PWR,” and then for volume, you obtain plus and minus signs. With out a more pronounced physical distinction, you are able to easier miss the buttons, and the frame moves inward when you press.
Twelve South is in the beginning about just how protective the SurfacePad is. In the FAQ part of the case’s website, the corporation says, “SurfacePad for iPhone is not designed to protect iPhone from falls, drops, being run over by a car or dropped within the loo. SurfacePad is supposed to guard your iPhone from scratches and scrapes from such things as car keys, nail files or concrete park benches.” It’s actually less of a case and much more of any leather sticker having a cover. The SurfacePad adheres to the back of the iPhone, and you will get rid of it and reapply it as necessary (though doing this is just not as elementary as the business could have you feel). We love to materials, although the SurfacePad is tough to recommend unless your main concern is fashion.
The Vault Slim Wallet from Silk is a much-less-expensive replacement for sister company CM4’s Q Card Case. It’s essentially the same design, except instead of a faux-leather back, everything is made from TPU. Like the Q Card Case, the Slim Wallet is capable of holding three cards, but an elevated arch within its card slot causes the cards to curve to some noticeable degree, which may damage the cards with time. The Q Card Case’s positive attributes otherwise carry over, but because of the card bending, I’m somewhat wary of the Slim Wallet.
Silk also offers the Armor Tough Case and PureView Clear Case. The Armor Tough Case is really a rubber case with interchangeable, polycarbonate-plastic backplates. It’s an excellent case at an affordable price, but it’s thicker than than our top pick, the NGP. The PureView Clear Case, on the other hand, is really a nice pick inside the very full type of cases with rubber edges and clear backs, and Silk prices it aggressively. But we’re not terribly fond of this style due to dust’s propensity to have underneath the transparent back, as a result of the convenience that the plastic can scratch. Still, beside others we’ve tested, the PureView Clear Case has pleasant-feeling buttons and well-sized port openings.
With Incipio’s Rival, unlike using the NGP, merely the border is TPU; the rest of the Rival is hard plastic, about .3 mm thicker than the NGP. Anything else in regards to the case is largely the same as around the NGP, including the cutouts for that ports and the standard of the button protection. Even though the Rival is very smooth, just like the NGP, horizontal lines across the lower two-thirds of the back include a distinct texture. It isn’t as neutral because the NGP, but if you like the design, this is a great choice.
Tech21’s Evo Mesh, which features another generation of your company’s shock-absorbing lining, is definitely an Apple Store exclusive. Similar to Tech21’s Classic Shell (more about this design below), it’s a rubber case using a colored band running around the perimeter. The dimensions are virtually identical between the two. There’s something concerning this one that people like more than the Classic Shell, but it’s challenging to put a finger on which that is. Perhaps it’s how the somewhat-obnoxious orange band has been replaced by colors matching the various body shades in the case itself. Overall, though, this example is too pricey for the purpose it provides you with.
Plastic and rubber with a clear back, the ITSKINS Venum Reloaded drops the ball in terms of covering the iPhone’s buttons. Just like the setup of Spigen’s Ultra Hybrid, the design in the Venum Reloaded makes virtually no physical distinction between the button coverage and the rest of the case. This example had also been relatively expensive when last we checked, as well as the plastic border frame feels fragile.
Really more of a fashion case, the Nitro Forged from ITSKINS currently costs a pretty penny at nearly $70. It includes rubber skin with machined aluminum caps that attach towards the top and bottom. Thankfully, this design is undoubtedly an improvement over previous versions, which required you to use an included screwdriver to set up and remove the caps; instead, it uses small plastic clips you could put in and remove yourself.
Also from ITSKINS is the Evolution. A rubber core having a plastic frame, the Evolution has some curves that assist help it become feel a little more organic. The large problem is that the screen rises higher than the fringe of the truth rather than the opposite. Which means that in the event you drop your handset, there’s a lot more potential for harm to the display than with other cases.
Incipio makes numerous cases that people can’t expect great things out from every one. The Advantage is really a plastic slider, a design that’s relatively rare currently. The smooth, matte-finish plastic splits into two pieces both for installation and docking purposes. Although it offers proper button coverage plus a nice protective lip, we found the case to become too tight; pulling it away, especially the bottom cap, can be a struggle.
Weighing a couple of grams more than the typical of all cases we tested, the DualPro SHINE is a solid contender from Incipio. It incorporates both plastic and rubber layers, although instead of being molded together, they’re two distinct pieces. The rubber is quite thick but doesn’t dampen the tactility of your buttons whatsoever, and it still provides acceptable access to the ports. The port openings are identical to the NGP’s. We checked out the standard DualPro, with a matte finish. It’s quite nice, but it’s thicker compared to the NGP and lacking the mil-spec rating of your CandyShell.
The plastic layer of your DualPro SHINE fits into grooves within the rubber, improving the case feel as if a cohesive unit. We think one of the most polarizing thing about this case is its texture: Made to seem like brushed aluminum, it certainly doesn’t seem like that, as well as at least in our tests, the result is actually a certain amount of cognitive dissonance. It’s not necessarily a bad thing at all, but overall it merely doesn’t feel quite as nice since it looks.
If card storage is important for you, Verus’s Damda can be a fine case. The body is made of black rubber, with nice button protection and effectively centered openings for the headphone port and microphone, the Lightning port, and the speaker. Connected to the back is a plastic compartment that adds both mass and depth. A plastic door slides accessible to reveal space for just two, maybe three, bank cards. We initially thought it was a little tough to open, however with some cards in there it’s easier to use but still secure. This is even more of a niche market case than our pick.
Verus’s Crystal Mixx provides a transparent window plus a rubber frame. The back on this one is plastic, which happens to be one of these two drawbacks. Within our knowledge about iPhone cases, clear plastic scuffs easily and will show those scratches within an issue of days. This case might not be so bad if the frame provided a better lip. Unfortunately, at .3 mm, it’s one from the shortest lips we saw, and it might lead to problems in the event you drop your iPhone.
The Protector Case and Voyager Case from Pelican look a good deal alike, and every model is difficult to acquire-Pelican doesn’t sell them online, as well as in our experience they’ve been reliably available only at AT&T retail shops. The Protector can be a bulkier, more-angular handle the CandyShell design with no additional benefits, so we’d pass into it. The Voyager adds port protection and funnels the sound through the speakers forward. Furthermore, it includes a belt clip and screen film. We notice this model as an option to an OtterBox case, as it’s basically overkill. A lot of people simply don’t need this level of protection, especially not in case they have to fall out of their strategy for finding it.
PureGear’s Slim Shell Case comes in seven color combinations, including clear-on-clear. This model is tough plastic having a rubberized yet still rigid frame. The metal button covers can be a great addition, improving the case feel more premium. It won’t offer as much protection being a CandyShell, therefore it isn’t a top-notch pick, but this one isn’t a poor option in any way.
One of the first iPhone 6 cases to get publicly sold-we saw it since May 2014-Minisuit’s Frost is undoubtedly an inexpensive TPU skin. Although it does fit, it offers very little lip, along with the holes along the bottom are uneven to the point of looking warped.
Monoprice is renowned for inexpensive products of all kinds. We like several of the company’s accessories-it makes great cables, for example-but Monoprice cases generally don’t impress. Materials often feel cheap, along with other companies offer higher-quality products at similarly discount prices. For instance, the Metal Alloy Protective Case (for sale in gold, silver, and cosmic blue) includes thin, aluminum shell that snaps over a thin TPU skin, with lines matching the iPhone’s antenna breaks. The TPU doesn’t feel as nice because the material that Incipio along with other companies use, as well as the case exposes the Apple logo on the rear of the phone.
Monoprice’s Industrial Metal Mesh Guard Case (in black or white) feels a bit nicer but is even less protective. The plastic shell has has a cool-looking steel grille over it, nevertheless it leaves the very best and bottom edges unprotected, and it also features the biggest Apple-logo opening we’ve seen on any case.
We looked at the TPU case from Insignia, a Best Buy brand, and it appear to be through the same OEM as Monoprice’s TPU case, but at a higher price.
We don’t much like the Monoprice PC TPU Protector Case as much, although it does offer arguably more protection. This model splits into two pieces, by having an inner skin of TPU and a polycarbonate shell that snaps into position over it. The way it is is fairly an easy task to assemble, but when it’s together, it merely feels big. It’s both wider and thicker compared to the NGP, without the obvious advantage besides price.
Rokform has long centered on ruggedized cases that could connect to an ecosystem of mounting accessories. Its Sport v3 is not any exception. This plastic and rubber case comes along with swappable magnetic backplates that allow it to hook up to various mounting brackets the organization sells. Unfortunately, the instruction insert lists a dealbreaker: “Magnet will disable NFC on phone.” Currently the business claims the magnet won’t interfere with Apple Pay or any antennas, but we haven’t tested this.
OtterBox’s Defender Series may be the bulkiest in the cases we’ve tested thus far. This is actually the company’s flagship case, the one a lot of people associate together with the brand. It’s made up of a plastic frame that snaps around the handset as well as a thick rubber skin that covers the whole thing. Unlike many other cases, this model includes flaps on the vibration control switch, headphone port, and Lightning port-all positive things for the extra level of protection. Furthermore, it includes button coverage, but we found out that it will require more force to depress the amount and power controls than other cases do.
The Defender Series can also be the only real case we’ve tested with built in screen protection by means of a definite film incorporated into the frame. Because you get a little space in between the protector along with the screen, very light presses and swipes may well not register, which is actually a drawback. Atop the Touch ID/Home button is really a thin sheet of plastic that didn’t hinder the ability in your testing. While the Defender Series does expose the Apple logo, the truth at least covers it with clear film that prevents it from getting scratched. And as a bonus, the Defender Series includes a belt holster.
From the OtterBox family, the Commuter Series represents the next thing down in overall protection. As opposed to plastic internally and rubber externally, the layers are reversed. The situation still offers port coverage, however the switch on the iPhone’s left side remains exposed. Thankfully, the buttons depress considerably more easily. Instead of a permanent screen protector, OtterBox includes an optional film with this particular case. The Apple logo is once more exposed, this period without any plastic covering it. Apart from the port protection, this case offers no obvious benefits over a CandyShell, along with the dimension is a drawback that keeps this model from earning a high spot.
The Symmetry Series can be a relatively recent addition to the OtterBox lineup as well as the slimmest of those all. It feels like a direct solution to the CandyShell, using its dual-layer design. This case supplies the same amount of protection as our top choice along with a substantial lip. It’s taller and wider, though, in a higher price. The biggest benefit is that by using a matte-plastic back, it won’t show the scratches a CandyShell does.
OtterBox’s newest case, the Statement Series, is definitely an iPhone 6/6s-specific case. An iPhone 6/6s Plus version exists, but unlike OtterBox’s other lines, this series offers no version for older iPhones or other flagship smartphones. It’s also one of the few OtterBox cases that put aesthetics first, using its large back-panel window and leather-covered lower quarter being its key distinguishing features. We’re testing the Statement at the moment, and we’ll decide whether or not this should join our picks soon.
The Tough Candy Cases Candy Clip Series is a fairly crazy proposition: For $30, you get a hard-plastic X-shaped piece that snaps onto the rear of the iPhone, covering its corners and several of the edges but leaving the buttons and most of the sides exposed. No thanks.
Urban Armor Gear’s Case is one of your only cases we’ve tested in order to meet military drop-test standards. It’s excellent as a protective case, nonetheless its industrial aesthetic lacks the broad appeal of simpler designs like those from Incipio and Speck. UAG also combines plastic and rubber in this case, but instead of a glossy finish, it utilizes a matte one, having an industrial appearance that appropriately matches the brand’s name. With ridges and fake screws, it seems like an issue that would not really out of place on the construction site. We do take trouble with both small, rectangular holes on the back of the truth-regarding a quarter of how through the top or bottom, respectively, they expose portion of the logo along with the top one half of “Phone” within the iPhone label. It’s an unusual design decision with an otherwise impressive case. Alternatively, this model does include a screen film, whereas most iPhone cases don’t nowadays.
Tech21’s entire product lineup will depend on D3O, a certified material the company uses in just about every one of its cases. Mostly found in the borders of Tech21 cases, the bright-orange material should really remain soft when at rest but automatically harden upon impact, dissipating the force and ultimately preventing problems for your phone. The company really likes to show off the stuff; every one of its cases are at least translucent, or even transparent, round the edges.
From Tech21, we tested the Classic Shell, Classic Shell Cover, and Classic Shell Flip. The very first is the most basic, a glossy TPU skin that’s wider compared to NGP, on account of the layer of D3O. We’d prefer to see a bigger lip than this example offers, as well as the buttons are a bit squishier than we generally prefer. The Classic Shell Cover keeps the same frame but replaces the TPU in the back using a hard-plastic plate, and it has an attached cover to safeguard the iPhone’s display. Everything else works just like with the standard model, as well as the lid carries a cutout across the earpiece so that you can speak on the phone by using it closed. The Classic Shell Flip is largely a similar, only rather than plastic this case features a leather feel (it looks to be the fake stuff), along with the lid comes around in the bottom rather than the side. We discover that lids get in the manner more than they guide, so neither of such covered models excites us, along with the soft buttons and wider body of the Classic Shell prevent it from receiving a recommendation.
From iLuv, we received two cases for evaluation: the Aurora Wave and Gelato. The initial one is a basic silicone skin having a grid around the back that glows at nighttime. When it comes to body coverage, the case lives up to what we’re seeking, but making such a design involves the lowest level of difficulty. As we’ve often found with cases of this style in the past, the vertical edges can pull away from the body of the phone more readily as compared to other cases, allowing dust as well as other particulates to have underneath. The Gelato, however, is iphone7 case with an attractive checkerboard pattern around the back. It appears and feels pretty good, although the .33-millimeter lip is simply too short.
Poetic’s Atmosphere is actually a thin case manufactured from dual-molded polycarbonate plastic and TPU. The softer material rings the top edge to make a small lip, and in addition it runs within the antenna breaks on the back of the phone. Even though this transparent case initially looks like a good option for people who want a slim protector but nonetheless want to show off their iPhone, it falls short due to button protectors that need excessive force to press.
Macally shipped us a few different cases, but two turn out to be styles we simply can’t recommend. The Metallic Snap-On Case and also the Flexible Protective Frame come in a variety of colors, although the former is a shell, and also the latter is a bumper that protects the sides but leaves the scratchable back exposed. The Durable Protective Case, in contrast, does offer more thorough protection, but unfortunately it isn’t an authentic design. A mixture TPU skin and hard-plastic frame, this example kind of appears like an armadillo through the back. We’ve already seen a minimum of one other company offering the same case, therefore we weren’t impressed with that case’s aggressive looks either.
New Trent’s Alixo 6S isn’t necessarily the prettiest case around, but it is one from the more original designs we’ve seen in the pile. This two-piece case consists of a front frame (black- and white-rimmed versions are in the package) along with a silicone rubber and plastic back. You simply snap the phone into your choice of frame then insert it in the back piece, consisting of flip-open port protectors. The quantity of protection this model offers for your price is impressive, as it incorporates a built in screen film and Touch ID coverage. But the latter happens to be the Alixo 6S’s downside: While the fingerprint sensor does work together with the thin material over it, we found so that it is less reliable, requiring more efforts to unlock the device.
Marblue’s ToughTek can be a thick silicone rubber case that is included with a screen protector. Basically we don’t doubt this thing should be able to tolerate some significant drops, the ToughTek is big-3 inches wide, 5.8 inches tall, and .6 inch deep-and particularly difficult to get in and away from tight pockets due to grippy material. It might not be described as a bad option if you’re handing your iPhone 6 to kids.
The Elite, also from Marblue, takes its inspiration in the CandyShell, while incorporating an Aztec-like pattern. The plastic and rubber layers intersect in horizontal and vertical lines, together with the latter material sticking up above the hard plastic. The most intriguing thing about this case is the pair of inch-long ridges, one on either sides. They’re made to do business with an array of accessories, such as a belt clip. We’ll be keeping an eye out for such accessories, and we’ll decide if they boost the value of the truth.
We had high hopes to the Spigen Capella, which comes in multiple colors. Its setup is much like the CandyShell’s, with rubber inside and plastic outside. The major difference, and also the reason we had been excited about it, is it’s much slimmer, measuring about 2 mm thinner from front to back. This is partly due to smaller, half-millimeter lip across the screen. One in our editors loves the way the case’s slight curve feels, comparing it to the iPhone 3G. Judging through the feedback we’ve seen from readers and Amazon reviewers, many individuals don’t such as that shape just as much as we do.
Although the Capella isn’t as deep since the CandyShell, it is actually a bit taller, and about 3 mm wider. This width eventually ends up being problematic for just two reasons, one on either edge. About the iPhone’s left side, the switch is significantly harder to toggle, as it’s deeply recessed in the rubber border; if you don’t have nails to talk of, moving it forward and backward will probably be tough. On the opposite side, the Sleep/Wake button requires a surprising quantity of pressure to activate. If you’re willing to manage those drawbacks, the Capella is otherwise worth looking at like a CandyShell alternative.
With its Revolution case, Poetic looks to contest with companies including OtterBox in a far lower price. The way it is commences with a plastic frame that snaps to the front in the iPhone; a specific sheet of plastic protects the screen while leaving the sensors towards the top along with the Touch ID button at the end exposed. A rubber and plastic body fits round the back, snapping into place using the front piece. Everything feels quite sturdy, the buttons click well, along with the flap over the Lightning port is really a nice bit of extra protection.
Supcase’s Unicorn Beetle Pro Holster supplies a similar proposition. The biggest difference between this model and the Revolution is that it includes a plastic belt holster. Having roughly the same dimensions as being the Poetic case, this model requires an installation that’s basically the same. This example adds a few flaps for coverage, namely across the side switch and the headphone port besides the Lightning port. While it’s an extremely solid-feeling case, we immediately called the company’s claim of dust-proof construction into question, as it leaves openings for dust to get in, such as the fully exposed speaker. Currently, Amazon users are generally fond of it, with 127 reviews plus a 4.1-star (from five) rating, but we’ve seen several three- and four-star reviews.
Relative newcomer Supcase has a variety of iPhone 6 cases, actually, nearly all of which are area of the “Unicorn Beetle” family. The Slim Armored Protective Case is similar to Urban Armor Gear’s case in this it’s protective, however the design is pretty specific, meaning it likely won’t interest a similar wide swath of men and women as something a little bit more generic. The plastic and rubber case feels sturdy and it has several of the clickiest buttons of the we tested. When it comes to lip, it’s no more than .5 mm, so it’s small compared to we’d like, and the case makes no mil-spec claims. If you want the appearance, it’s not a bad choice otherwise.
Supcase also sells the Hybrid Clear Bumper Case, which combines a precise-plastic backplate using a TPU bumper. That polycarbonate back won’t absorb all the shock since the thick rubber border, but it’s the best way to display Apple’s design.
In a previous version of the guide, we named Logitech’s Protection [ ] as a much more-protective pick. It features a very similar design, with the benefits of a matte finish and embedded magnets that give it time to get connected to mounting accessories. Unfortunately Logitech has confirmed that it’s will no longer selling the situation, which is currently on clearance at Best Buy.
Hardly any other case we tested is placed the same way as Maxboost’s DuraShield Series (now named DuraSLIM). Like many other models, it uses both rubber and plastic components, but here the rubber is really a bumper that wraps round the iPhone’s border, along with the plastic snaps set up over it while covering the rear of the handset. Inspite of the unusual design-or perhaps for doing it-the way it is offers superior protection in comparison with many others we’ve seen. It contains a 1-mm lip, plus speaker and Lightning-port protection. It also redirects the audio ports forward, meaning the sound comes to you, instead of down; the design has no impact on audio quality, thankfully. With regards to Lightning port, it stays protected underneath a rubber tab that you could flip out when you really need access.
Few case manufacturers actively warn their product doesn’t offer drop protection, but this kind of message appears in the Amazon listing for Maxboost’s Liquid Skin. Extremely thin, this transparent-TPU case adds very little bulk towards the handset, not actually a protective lip. It’s much better than a shell mainly because it offers button protection and cutouts for that ports, even when they are quite tight. Although with such a warning in the case maker itself, we can’t recommend the Liquid Skin for many individuals. If you’re going try using a case, you should utilize something that’ll withstand a drop.
Maxboost’s Crystal Cushion and so i-Blason’s Halo Series are almost identical to each other and might be small tweaks on the very same reference design. Both have rubber frames-the Halo Series offers six colors, plus clear-with transparent plastic backplates. The Maxboost case’s edges are definitely more squared-off, as the i-Blason’s are rounder. Both offer good body coverage and responsive buttons, however the lip across the screen is nearly nonexistent, especially in the Halo Series. Combine that with the tendency for clear plastic cases to scratch as well as to expose trapped dust underneath, and these cases aren’t top picks.
The Maxboost HyperPro Series is made for all intents and purposes a thicker version from the Incipio NGP. Available only in black, it uses two layers of TPU to safeguard the iPhone, and it measures 10.2 mm thick; it’s also wider and taller than our pick. The buttons press well and it contains a protective lip, but we can easily find no real advantage of this situation within the NGP, aside from savings of just a couple dollars.
One of only a few slider-style cases around, Maxboost’s Vibrance Series supplies a different build than most of the cases we tested. A tough-plastic case, it splits into two pieces, both lined with a soft fabric over the back that’s created to prevent damage during installation and removal. As opposed to pushing the phone to the case, you pull off the bottom cap, slide the phone in the top, and then push the pieces together again. Much just like the STM Harbour, this kind of design allows you to maintain the iPhone thoroughly protected usually, as well as plug it into docks when needed. The lip is almost short, though, and pulling from the Vibrance’s bottom cap is harder than flipping within the Harbour’s bottom. Maxboost even offers only one color choice, salmon using a gold cap, which might not attract as numerous people as increasing numbers of basic colors would.
If you realise the CandyShell to become too big, you won’t be impressed with Speck’s MightyShell, which is available in black, orange, purple, pink, and clear variants. This model does have a number of key differences. First will be the extra layer of TPU material that helps absorb shocks to some greater degree; it adds 2 mm both in width and height, along with .5 mm for the thickness of the case. Speck claims that the new design will “double MIL-STD-810G drop test standards,” but we can’t tell whether it means the truth is tested to thrive drops from twice as high or this means the situation can tolerate the conventional 4-foot drops twice as many times. One aspect of the case we really appreciate is the hard-plastic exterior, which happens to be matte as an alternative to glossy, therefore it won’t show scratches nearly as readily since the standard CandyShell. For the price, we expect more than just claims of better drop protection; conditions by which this case would survive but a CandyShell wouldn’t are too ambiguous to justify the fee.
Among ultrathin cases, Shumuri’s SLIM looks and feels very similar to Caudabe’s The Veil XT, to the lack of the conventional Veil’s screen-protection lip. But it’s also missing both Veil models’ camera-lens protector. The same goes for Monoprice’s Ultra-thin Shatter-proof Case (in clear frost, ice blue, and smoke) and Totallee’s The Scarf (for iPhone 6 and iPhone 6 Plus).
Rearth USA’s Ringke Slim (for iPhone 6 and iPhone 6 Plus) offers both a screen-protecting lip and bottom-edge coverage, as well as thicker plastic for additional protection. However, we’re not fans of its aesthetics-for the reason that case’s rigid plastic is thicker, the corporation has added a small slit to every corner to make putting the way it is on the phone easier. The design works well enough; we just don’t like the actual way it looks.
Power Support’s Air Jacket and SwitchEasy’s Nude (for iPhone 6 and iPhone 6 Plus) are glossy-plastic cases that happen to be slightly thicker than Caudabe’s The Veil. The former provides good coverage along the phone’s bottom edge but has only the particular faintest of the screen-protection lip. The latter has neither.
Amzer’s Crusta may well not seem like a great value at $35 (iPhone 6) or $45 (iPhone 6 Plus) since this writing, however the package has not only a simple case. The way it is itself utilizes a two-piece snap-together design using a rubber bumper and a glass back that lets the iPhone’s rear show through. The glass likely won’t show scratches as easily as similar cases we’ve seen using a plastic back, nevertheless, you will still see any dust, hair, or other particulates that will get under the glass. Amzer features a second part of glass to shield the phone’s screen. The way it is ultimately ends up being bulkier than we prefer-the iPhone 6 version is 14.4 mm thick, for example the phone-but it’s one in the better cases we’ve seen from Amzer, a firm otherwise renowned for inexpensive, nondescript accessories.
NewerTech is recognized more for computer accessories than smartphone accessories, nevertheless the company does provide a line of cases called NuGuard KX (for iPhone 6 and iPhone 6 Plus). Made more for drop protection than sleekness, the NuGuard KX incorporates a thick layer of gel material that absorbs and evenly distributes shocks. The situation is very bulky, yet an opening on the rear of the truth for your phone’s Apple logo actually subtracts through the overall level of protection. We prefer the NGP.
We certainly have varying levels of praise for three cases from Griffin Technology. The Survivor Slim (for iPhone 6 and iPhone 6 Plus) is our least favorite of those. This bulky rubber case feels similar to an accessory to get a kid’s toy than a smartphone. It can be an effective case if children frequently make use of phone, but we suspect that many adults will prefer something slimmer.
We love to the Survivor Core (for iPhone 6 and iPhone 6 Plus) and all sorts of Clear Identity (for iPhone 6 and iPhone 6 Plus) better. Both enable the handset’s to show by way of a clear back panel. The previous has rubber edges, along with its rubber corners protrude a bit, and helps to cushion the iPhone against drops-nevertheless the result is that it’s a little larger than a regular case. The All Clear Identity, on the flip side, carries a transparent back with translucent-rubber edges. The trouble, as with most cases sporting a definite back, is that both cases show any gunk that gets under the plastic. For many people, that may be an acceptable compromise in the case designed to let you see your phone’s own surfaces, but we generally prefer something translucent or opaque. Neither the Survivor Core nor the All Clear identity is actually a bad option, but neither particularly excites us.
Belkin’s Grip Case for iPhone 6 is a superb replacement for our top pick, but it really doesn’t quite make your top tier. The design is much like those of the Incipio NGP, as it’s a one-piece polyurethane case. The greatest difference is over the phone’s bottom edge: As an alternative to having separate openings to the headphone jack, microphone, Lightning-connector port, and speaker, the way it is exposes the past two through one long opening. A small indentation within the plastic covering the foot of the phone enables use with accessories for example Apple’s Lightning-connector adapters. This really is a nice feature that we haven’t seen on other cases, although we worry how the thinness from the material here, as well as near to the Ring/Silent switch, will make it more prone to ripping. Wirecutter editor Michael Zhao also finds the case’s button coverage to become somewhat problematic, as he doesn’t like this they’re nearly flush using the case.
Among the cases shipped to us for consideration, we also dismissed a number of models right from the start. We cut Spigen’s Slim Armor, Slim Armor S, Tough Armor, and Tough Armor S, along with Verus’s Thor, Iron Shield, and Dandy Diary, plus PureGear’s DualTek, because of the Apple-logo-exposing holes on the back. They actually do a good job of protecting your phone otherwise, but we can think of no reason to recommend them for many individuals when existing hole-free options are pretty much as good or better.
We dismissed numerous shell cases because, as we mention above, they offer a minimal level of coverage for your device’s body. Among these were the Aluminum Fit, Thin Fit, and Thin Fit A from Spigen. The same goes for your Neo Hybrid EX, Spigen’s bumper case, which offers much less protection.
This post first appeared on Dental Health Is Important: Utilize These Recommendations, please read the originial post: here