Get Even More Visitors To Your Blog, Upgrade To A Business Listing >>

5 Common Well Pump Problems and How to Fix Them

Tags: pump

5 Common Well Pump Problems and How to Fix Them

Is your water well Pump acting up and giving you the blues? Are you tired of living in a dark age with a faulty pump well? If you are living in Fallon and rely on water well pumps, then this might be a common issue you are facing.

A functional pump is necessary if you have a private water well in order to get water into your house. Even if you definitely don’t want it to stop functioning, problems may nonetheless arise from time to time. Many minor issues with your well pump might result in more costly repairs or possibly replacement if left unattended.

Some problems might seem pretty clear. Some might mask themselves with issues that you cannot even understand – and trust me, they are not that major.

In this blog, we have covered 5 common well pump issues. We have also mentioned how you can fix it. So, let’s get started with your solution to your problem of water well pumps Fallon, NV.

What are the Signs of a Faulty Well Pump?

Pumps usually last for 8 to 15 years. Some can even last for 20 years or longer. When it is time for your pump to be replaced, it will exhibit the following signs –

  • Fluctuations in water pressure
  • Constantly running pipes
  • Sediments in water lines
  • Unusual sounds from pipes
  • Change in water quality

However, you must keep in mind that just because your pump is acting up or showing any signs, as mentioned above, it does not necessarily mean it is dying. Sometimes, they just need a little fixing. If you are looking for a water pump replacement, Reno, consider confirming all other components before hoping to make a decision.

Common Well Pump Problems (and How You Can Fix Them)

Here are some common well pump problems –

No Power in the Pump

This is one of the most common problems you might face. But first thing, you should check the circuit breaker to see if your well pump isn’t working. Proceed to inspect the fuses and power lines if it hasn’t tripped. Likely, your well pump’s circuit breaker is off if your well pump isn’t working. Here’s how you can check them out –

Make sure the circuit breaker is on. Turn it on if it’s off. Before inspecting the pump, make sure the electrical system is functioning properly if you have a submersible well pump.
Check if the cables that go from the breaker box to the submersible pump are back wiring for any electrical shorts. There won’t be enough voltage to run your well pump if there is an electrical short in these lines. In such cases, the defective wiring needs to be replaced.
Check for loose connections. It’s possible that these connections came loose during installation or as a result of aging and use. To ensure that any issues are resolved before they worsen in the future, it is essential to seek assistance from a well-pump professional with experience in handling electrical systems. You can call an electrician if that’s the issue.
If there are no problems with connections and electricity, there might be a problem with your pump switch or motor.

Pump Cycling Too Quickly

A condition known as quick cycling occurs when the water pump quickly switches on and off. There are a number of potential causes. Therefore, understanding the issue is crucial before changing the pump.

A fast-cycling pump may be the source of your water supply issues. The pump may cycle on and off every few minutes or seconds if you have a well and every few hours or days if you use city water.

Here are some of the common reasons for pump cycling too quickly –

  • Low Water Level: The pump will run more frequently than usual to keep up with demand if the water level in your well is low. This issue can be avoided by using a low-water alarm, which notifies you when the level is too low.
  • Inadequate Pressure Switch: A pressure switch regulates the on and off times of your pump. You should make sure that corrosion or bad electrical connections aren’t the reason this part isn’t working properly.
  • Corrosion: Over time, corrosion brought on by minerals in your water supply may lead to issues with your well system. This could lead to your water pump operating inefficiently or possibly causing harm to other components of your system.

Pipe Leaks

It’s important to inspect the plumbing for leaks if you have a water well pump Fallon, NV. Turn off the pump and check the water line for bubbles. If you find any, your system has a leak that needs to be fixed before you switch on your pump once more.

Here’s a small tip on how you can fix the leaks –

First, check if the valves can be changed out with new ones that you can buy at a home improvement center or irrigation supply store. They are affordable and can last for up to several years before needing to be changed. Depending on how old they are, other pressure tank system components could also need to be replaced.

Modern models are more likely to break over time as a result of age- and use-related wear and tear. Furthermore, rust and other acidic materials that accumulate inside pipes as a result of daily exposure to mineral deposits from running water might cause corrosion. Thus resulting in the faulty water pump.

Low Water Pressure

Various factors can cause low water pressure. Your well pump may be outdated or not operating as it was before. For any reason, you should take immediate action to fix low water pressure in order to prevent damage to your water well system.

Numerous issues can arise from low water pressure. It will take longer than usual for the water to get to your house. Major causes of low pressure can be –

  • Broken well pipe
  • Aging well pump
  • Clogged faucets
  • Clogged well screen
  • Pressure switch setting

To prevent this, you can either go for water well replacement, Reno. You can also contact a professional if you have broken pipes.

Air in the Pump

If your pump is pumping air or is causing water to stumble, this means there is something wrong with the pump. This mainly happens due to low water levels. The pump is unable to draw in enough water to match its flow. This causes air to mix with water, causing spluttering. Spluttering water can also be a signal for your pump to be reprimanded to remove any air in it.

To check the air in the pump, turn it off. Once done, allow all the water to drain out of it by opening your faucets and running them until the water stops flowing. Reconnect everything after that and restart, being careful not to turn on any more faucets.

While performing this test, if you turn on another faucet, some water may still stream out of it since some pipes’ pressure may have remained after they were drained.

After everything has been connected again, check each pipe that emerges from under your appliances before using any more (such as dishwashers or washing machines).

Takeaway

Water pumps are important for various applications. Hence, any inconvenience can cause disruptive water flow. Understanding the problems and their causes can help fix the water pumps. They can kept up and running by regular maintenance, inspection, and replacements of worn-out parts. If you are finding any minor issues with your water pump, contact a professional for water well pumps Fallon, NV.

Take it Easy With a Properly Maintained Pump.

At Bruce Mackay, we specialize in repairing pumps and water well pump drilling Winnemucca. Our technicians make sure to evaluate your water well properly and efficiently. Also, we use high-quality tools and advanced technology to ensure your pump runs smoothly.
Whether you need a quick fix or a complete overhaul, get in touch with us to schedule a consultation.

The post 5 Common Well Pump Problems and How to Fix Them appeared first on Bruce Mackay.



This post first appeared on Bruce MacKay Pump & Well Service, Inc., please read the originial post: here

Share the post

5 Common Well Pump Problems and How to Fix Them

×