Welcome to Fun with Less Kilowatts! We believe that science experiments at home can be a creative way to engage kids in learning while having fun. They can be educational AND great activities to keep your kids busy and away from the television. Each month, we’ll feature a new science experiment that can be a great resource for parents and teachers.
Did you know you that the energy from radio waves can be converted back into electric energy? It’s true and you can make a simple two-component circuit that you and your kids can use to find 2.45 Ghz radio waves around your home. These are the same radio waves used by microwaves, WiFi network routers, bluetooth devices, smart phones, cordless phones, smart meters, and smart home systems that use Zigbee.
YouTuber pjaffeva posted this brilliant project showing how. Plus, there’s also a link to a PDF set of instructions on Google Drive that you can download.
- One HLMP-D150 Avago low current LED. Costs about 50¢/each. Available from: Amazon, Digikey, Mouser
- One Hitachi 1SS106 low capacitance Schottky diode. Pjaffeva recommends this Hitachi-made diode as being the only one in this shape that will work. But they’re also hard to find. Currently, you can get them from LittleDiode’s ebay store in the UK. Costs $6.38 but the bulk of that price is shipping from the UK.
You’ll also need:
- An operating WiFi router
- A bamboo kabob skewer
- Two pieces of tape
1) Look on the base of the LED and find the side with the flat edge. This marks the negative or cathode side. Carefully splay the two wire leads away from each other as far as they will go. Make sure the one adjacent to the negative side gets bent over the flat edge so identify it. You can also mark it with a little spot of colored nail polish.
2) Next, find the band that runs around the Schottky Diode. This identifies the negative end of this diode. The other end is the positive or anode end.
Using your fingers:
3) Twist the end of the negative or cathode wire from the LED onto to the positive or anode end of the Schottky Diode.
4) Then twist the end of the negative or cathode end of the Schottky diode onto to the positive or anode end of the LED.
You have just made a “rectenna” and you’ll need to keep the assembly and the wires straight as possible. The length of the wires should be about 6 cm long (a hair short of 2 3/8 inches).
5) Tape the two diodes to one end of the bamboo skewer.
6) With a WiFi router on and running, hold the diode near an antenna on the WiFi router.
The LED should light up as it draws closer to the antenna (signal). The further away it is, the weaker the signal and the less it can grab to light up.
The WiFi routers uses radio waves to transmit data to and from computers and other devices in your home. Radio waves behave like water in a glass, they ripple or oscillate at a certain number of times or frequency per second. A radio wave’s wavelength is the distance covered by one complete cycle of a radio wave — from peak to valley.
Radio waves used by WiFi routers, bluetooth devices, microwaves, etc., broadcast signals in the 2.45 gigaherz (Ghz) range or 2.45 billion oscillations per second. That means the signal wavelength is about 12 cm. To pick up signal, however, you only need an antenna that’s half as big—6 cm. When the radio waves strike this antenna, called a 1/2 dipole (“di”=two), the energy excites the antenna’s material, causing electrons to move and create voltage that moves down both poles of the antenna.
The “Rectenna”: Because the radio waves cause voltage to flow one direction and then the opposite direction, the current is called an alternating current (AC). By connecting a diode to both poles of the antenna it converts the AC current to flow only in one direction, called direct current (DC). The antenna becomes a “rectenna”.
How the diodes work: The diodes work as one-way valves for electricity, allowing voltage to flow forward but not back. In the case of the rectenna, AC current caused by the radio wave sends a positive charge down one of the antenna poles and then the other. By putting the Hitachi 1SS106 diode across both poles, the diode only lets the positive charge coming down one of the antenna poles through. The LED is actually a Light Emitting Diode and works the same way as a regular diode except that when it’s on, it lights up. Meanwhile, Schottky diodes turn on at a lower voltage than other diodesand because the rectenna can only catch a fraction of the WiFi’s broadcast power, the Schottky diode can rectify that little bit of AC to DC.
When we connected our diodes together, their polarity formed a loop that only allowed voltage to flow one way and thus light the LED. Brilliant job, pjaffeva!
Do you have any fun and kid-friendly science experiments you’d like to see us try for Fun with Less Kilowatts? Share with us in the comments!