When I began making audio recordings of Interesting Thing of the Day articles, I immediately realized that my office was not acoustically appropriate. There were too many extraneous sounds—fans, hard drives, and so on—and my fancy new microphone picked them all up perfectly. So I decided to set up a little recording studio for myself in a closet. The closet door nicely blocked out the sounds of the room, as well as most of the sounds from other parts of the house, traffic outside, and so on. The problem was that the recordings sounded like I was in a closet, or maybe a bathroom—the flat walls and ceiling added an unpleasant reverberation to my voice. In professional recording studios, the walls are usually covered with special acoustic foam to absorb most of those reflected sounds and give the sounds being recorded a more pristine character. I didn’t have any acoustic foam handy, so I covered the walls with old blankets instead. That did the trick: now my voice sounds correct, and I can always add reverberation or other effects later if I feel the need.
Recording studios are generally designed both to keep outside sounds from being heard inside the room and to keep sounds generated inside the room from bouncing around enough to be picked up by the microphones—and they invariably do a better job at both than my makeshift studio-in-a-closet. However, they’re still far from soundproof or acoustically “dead.” A noisy motorcycle or heavy truck coming down the road outside might still be heard inside, and the surfaces inside the room still reflect a bit of sound.
Is There an Echo in Here?
If you’re recording a CD, these minor imperfections in the room’s acoustic quality are no big deal. But if you’re trying to perform delicate, highly accurate measurements of the dynamic response of a microphone or the frequency range of a speaker, any reflections or unintended sounds at all can invalidate your tests. So you need a heavier-duty soundproof environment than a recording studio: you need an anechoic chamber.
The word “anechoic” means, as you might guess, “without echoes.” Naturally, an ordinary room is going to reflect sound less than a canyon or a concert hall, but making a room completely immune to sound reflections is surprisingly difficult. The first step is to consider the angles of the surfaces in a room. Flat, hard surfaces reflect sound best, and when you have more than one such surface—especially when they’re parallel—you’re guaranteed to have some sort of echo. Then you have to consider the composition of the walls, floor, and ceiling. A given material (think of the blankets lining my closet walls) may absorb certain frequencies of sound effectively, while reflecting higher or lower frequencies. In addition, sound volume comes into play: materials that absorb relatively quiet sounds may nevertheless partially reflect louder sounds.
So most Anechoic Chambers have all their interior surfaces lined with thick wedges of fiberglass (or in some cases polyurethane) foam. The wedge shape traps sound waves by reflecting them onto another part of the wedge rather than back into the room. The foam itself then absorbs the vibrations (turning them into heat). The deeper the wedges are, the lower the frequencies of sound that can be absorbed. To absorb all sounds within the range of human hearing requires immense wedges, shrinking the interior space of the room and adding to its cost. Meanwhile, it’s equally important to prevent sounds from the outside from entering the room. The walls themselves (behind the foam wedges) must be quite dense and thick; in addition, anechoic chambers are generally isolated from the rest of the building by “floating” them on a set of large springs.
The Cone of Silence
I’ve never been inside an anechoic chamber myself, but my friend Darren has. Darren is a record producer, and he uses his considerable audio engineering talent to turn my raw voice recordings into the polished programs heard every day by our audio subscribers. He once visited an anechoic chamber used for testing microphones at the Peavey Electronics headquarters in Meridian, Mississippi. Darren described the experience as being just like walking into Cerebro, the psychic amplifier created by Professor Xavier in the X-Men comics and movies. Because the floor, ceiling, and even the door of an anechoic chamber must be kept as free as possible of reflective surfaces, the working area is a small stage suspended in the very center of the room, accessed by a long walkway. The walkway and stage included handrails because people inside the chamber frequently become disoriented. Although we are not normally conscious of it, the tiny reverberations from sounds hitting the walls, floor, and ceiling of ordinary rooms are picked up by the inner ear and used to enhance our sense of balance. Without these cues, it’s harder to know which way is up.
Darren described the experience of utter silence in the room as being very strange. Because there was no ambient noise at all, the smallest sounds—a whisper, the sound of breathing, or even a shoelace flapping—seemed astonishingly loud. But the important thing for the technicians testing audio equipment in the chamber is that if they’re measuring the sensitivity of a microphone or the output of a speaker, they can be certain that only the sounds they deliberately generate inside the room have an effect on their test equipment.
Other Other Echoes Echoes
Although anechoic chambers were originally designed as places free of sound echoes, the term “anechoic chamber” is also used to describe a type of room specially designed and shielded to prevent the reflection of radio waves and other electromagnetic radiation. Manufacturers use such chambers for testing antennas, radar equipment, and other electronic devices that produce radio waves, to ensure that their measurements do not include any reflected signals. The materials and designs used to prevent the reflection of radio waves are different from those used in conventional anechoic chambers, but the basic principle is the same: absorb, don’t reflect. Interestingly, though, some anechoic chambers designed for electronics actually have surfaces that reflect sound quite well.
Being a city dweller, I’m accustomed to a certain amount of background noise 24 hours a day. At the same time, I can do without the more obnoxious sounds of traffic, loud music, shouting, sirens, and so on. Even though the absolute silence of an anechoic chamber sounds delightful for a meditative retreat, I imagine the novelty would rapidly wear off. If the sound of my own breathing became distracting, I may be on my way to a padded room of another kind. —Joe Kissell
Permalink • Email this Article • Categories: Music & Sound, Science & Nature
More Information about Anechoic Chambers...
Read Anechoic chamber in the Wikipedia for a brief overview of anechoic chambers.
For more information on audio anechoic chambers, see:
- The Murray Hill anechoic chamber
- ISVR Consulting’s Large Anechoic Chamber
- McIntosh Anechoic Chamber
- The University of Iowa Electronic Music Studios anechoic chamber
- The UK’s Health and Safety Laboratory anechoic chamber
For more information on EMF anechoic chambers, see:
- The Virginia Tech Antenna Group anechoic chamber
- Big Price, No Echo (PDF) at Conformity
- Turnkey Chambers at TDK RF Solutions, Inc.
When I created my recording-studio-in-a-closet, I encountered another problem: how to control the software on my computer, which was outside the closet (so the microphone would not pick up its noise). I solved this by using my Bluetooth-enabled cell phone as a remote control, thanks to a piece of software called Salling Clicker. You can read more about my experience in Salling Clicker in Action, an article I wrote for TidBITS.
Related Articles from Interesting Thing of the Day
- Silent Retreats
- The Tactile Dome
- The Right-to-Quiet Movement
- Missile Silo Homes
- Array Microphones
- Quiet Parties
℗ & © 2004, alt concepts. All rights reserved.