Get Even More Visitors To Your Blog, Upgrade To A Business Listing >>

Application and Uses of Bunsen’s Ice Calorimeter

Application and Uses of Bunsen’s Ice Calorimeter

The Bunsen’s ice calorimeter is a device for measuring a quality of Heat by using it to melt ice. When ice turns to water, it shrinks; the volume of 1g of ice at 0oc is 1.0908 cm3, whereas that of 1g of water at 0oC is 1.0001 cm3. Thus the melting of 1g of ice causes a contraction of 0.0907 cm3

In the Bunsen’s ice calorimeter, the contraction due to the melting is measured, and from it the mass of ice melted is calculated. The apparatus used in carrying out the experiment consists of a test-tube T fused into a wider tube Y. the wider tube leads to a capillary C, and is filled with mercury from X to Y. the space above Y is filled with water from which all dissolved air has been boiled. Except for the capillary, the whole apparatus is placed in ice – water in the vessel V, and after some time, it all settles down to 0oC. A little ether is then poured into T, and air is blown through it via a thin tube; the ether evaporates and cools the tube T, so that ice forms on the outside of it. A pad of cotton wool is then dropped to the bottom of T and the apparatus is left for some more time, to allow the newly formed ice to settle down to 0oC

When the apparatus is ready for use, the end of the mercury thread in C is observed by a traveling microscope. If the specific heat capacity of a solid is to be measured, the specimen is weighed (m g) and left to come to room temperature 0. The solid is then gently dropped into the tube T. as it cools, it melts ice, and causes the mercury thread to run back along the capillary is a cm2, when the thread has ceased to move, its end is again observed. If is has moved through l cm, and the cross-section of the capillary is a cm2, then the contraction is al cm3. The mass of ice melted is therefore al/0.0907 g, and the heat absorbed is 334 al/0.0907 joules. Thus heat is given out by m g of solid cooling from 0 to 0oC; the specific heat capacity c of the solid is therefore given by

    Advantages of the Ice Calorimeter

The advantages of the bunsen’s ice calorimeter are:

  • No correction for heat capacity of the container: the specimen tube starts at 0oC and finishes at 0oC – all the heat from the specimen is used to melt ice, at constant temperature;
  • No heat losses from the apparatus – it is surrounded by a bath at the same temperature as itself, and therefore neither loses heat to the same temperature as itself, and therefore neither loses heat to the outside, nor gains any from it;
  • No loss of heat from the specimen before it enters the calorimeter – the specimen starts at room temperature, and therefore gives up no heat until it enters the specimen tube (contrast the method of mixtures, in which the specimen is heated to 100oC or so) ; this is a great advantage when the specimen is small;
  • Easy, and therefore accurate, thermometry – the only temperature to be measured is the room temperature, which is constant and can be determined at leisure.

An advantage sometimes asserted is that specimens can be added one after another, without having to re-set the apparatus. That is true, because each specimen comes to 0oC in turn, and then behaves simply like part of the apparatus, taking no heat from any following specimen. But it does not mean that the calorimeter has the advantage of speed – the time taken to set it up would be enough for half a dozen measurements by the method of mixtures. A disadvantage of its calorimeter is that it never settles down completely – the mercury is always slowly creeping along the capillary, and the creep during an experiment must be estimated and allowed for.

 

Info
The calorimeter was devised in 1871; it is rarely used nowadays, because electrical methods of calorimeter are more convenient and accurate.
However, it has been used for measuring the specific heat capacities of rare earths of which only small specimens were available.

                                Evaporation

The specific latent heat of evaporation of a liquid is the heat required to convert unit mass of it, at its boiling – point, into vapor at the same temperature. It is expressed in joule per kilogramme (Jkg-1), or with high values, in kj kg-1.

To find the specific latent heat of evaporation of water, we pass steam into a calorimeter with water. On its way the steam passes through a vessel, T in the figure, which traps any water carried over by the steam and is called a steam-trap.

         

            Berthelot’s Apparatus

An apparatus suitable for use with liquids other than water was devised by Berthelot in 1877. The liquid is boiled in the flask F, and its vapor passes out through the tube T. this fits with a ground joint G into the glass spiral S, which is surrounded by water in a calorimeter. The vapor condenses in the spiral, and collects in the vessel V, where it can afterwards be weighed. Let

0b = boiling – point of liquid.

c = specific heat capacity of liquid.

m = mass of liquid condensed.

01 = initial temperature of water

02 = final temperature of water, corrected for cooling.

m1 = mass of water of specific heat cw.

C = thermal capacity of calorimeter + glass ware below joint.

ice calorimeter photo


The post Application and Uses of Bunsen’s Ice Calorimeter appeared first on GulpMatrix.



This post first appeared on GulpMatrix, please read the originial post: here

Share the post

Application and Uses of Bunsen’s Ice Calorimeter

×

Subscribe to Gulpmatrix

Get updates delivered right to your inbox!

Thank you for your subscription

×